It sounds like you currently have the older Replacement Basic Wall Thermostat for Furrion Chill RV Air Conditioner - Single Zone - Black FACW12SA-BL. You can indeed change it out for the Premium Wall Thermostat for Furrion Chill RV Air Conditioner - Single Zone - Black # FR33PR. I included a demonstration video for you. view full answer...
The Global Link RV Baggage Door Slam Latch, # 295-000015, is a replacement to Global Link, Fastec (FIC), Bauer, and Lippert Components standard baggage door lock. These are the primary vendors to most all OEM RV builders. The dimension of this particular lock is 5" wide x 4-1/2" tall x 1-1/2" thick. If the lock on your 2021 Grand Design Imagine Travel Trailer has markings showing to be produced by one of these manufacturers and meet these dimensions, then yes this will work as a replacement... view full answer...
The Cheetah is one of the many designs that has been discontinued by Lionshead. Although we do have the 14" x 5" the 15" version is no longer available. I understand this can be frustrating, especially when your trailer is not very old. The closest design we have is the Aluminum Viking Series Vor Trailer Wheel # AX02550545FPS which is a 15" x 5" wheel. This would be fine if you're just looking for a spare, or if you want to replace all of the wheels to match. For 15" x 6" we have the #... view full answer...
The Hub Bearing Kit # BK2-100 is the correct kit for the 3,500lb axles on your 2022 Grand Design Imagine 2400BH. This provides the bearings, races and a grease seal for 1 hub. We do have the Seal Puller # PTW1219 and Bearing Packer # PTW1218 to make repacking the bearings much easier. I recommend using the Grease # L11390 and Grease Gun # L30416 to fill the bearings. This grease is designed for use in extreme temperatures and pressures and is highly water resistant. view full answer...
To replace your Cavagna 924 regulator you can use the Camco Regulator # CAM59005. This is a 2 stage automatic changeover regulator for a dual take setup and will be very similar to your Cavagna regulator. view full answer...
Appreciate all the information provided, as that was all that was needed to get you the right bearing kit for your 2021 Grand Design Imagine 2500RL with 3,500 lb axles. What you need is the following:
- Hub Bearing Kit # BK2-100 view full answer...
What you have on your 2019 Grand Design Imagine 22RBE is a 3,000 lb Dexter axle. The inner bearing is # LM67048 and the outer bearing is # L44649. The correct grease seal is the # RG06-050 (10-19). view full answer...
The spring center length on your current axle does not matter when it comes to finding a replacement. The most important piece of information is the length of the axle, which is the hub face to hub face measurement. As long as the hub face measurement matches up you can adjust the spring center by cutting off the existing spring seats and welding on # TRSS238.
If your hub face measurement is 89" then you could use the Trailer Axle Beam with Easy Grease Spindles - 89" Long - 3,500 lbs #... view full answer...
The MORryde cushioned suspension equalizers like the CRE3000 part # MR27ZR that you referenced do not affect the height of the trailer at all.
If you wanted to lift the trailer you could use the Correct Track lift kit part # RR23QX as well. view full answer...
The hubs used by the Dexter 4400 lb axle are 3500 lb hubs that have had their weight capacity upgraded by using a LM67048 outer wheel bearing. A 4400 hub like the # 8-407-5UC3-EZ would use the same # 58846 grease seal as a 3500 lb hub would.
Long story short, the correct grease seal for your Dexter 4400 lb axle would indeed be the # 58846. view full answer...
The Aluminum Cheetah Trailer Wheel from Lionshead was discontinued so if you're needing a replacement silver 15" wheel with that 5 on 4-1/2" bolt pattern I recommend checking out the Lynx # LHSL301 wheel instead.
Attached is a review video for you to check out. view full answer...
Thank you for the details!
The Road Armor line doesn't really have anything that matches up so we'll want to look at the MORryde and Dexter Axle options.
For the MORryde we have the kit # MR27ZR which is a little longer and lower but will still work out just fine since those greater measurements are still under an inch so I recommend going this route.
If you want something more exact then the Dexter E-Z Flex Suspension Kit # K71-653-00 is about the same length and height as what you... view full answer...
The Dexter 4400 lb axle is a bit of an oddball, so we don't have a bearing kit for it, but we do offer everything you'd need to assemble one.
Here's what you'd need:
• Inner Bearing # L68149
• Inner Race # LM68111
• Outer Bearing # LM67048
• Outer Race # LM67010
• Grease Seal # 58846 view full answer...
A lot of the 4,400 lb axle will use the bearings and seal kits for a 3,500 lb axle so if that's what you have then the Hub Bearing Kit # BK2-100 is the correct replacement kit.
The 4,400 lb axles can be a bit hit and miss though so you'll need to either pull a hub to check that you have the matching parts that come with this kit (see list below) or you'll need send me a photo of the axle tag so I can see what exact parts you need.
Bearing Kit Parts:
Inner Bearing - L68149
Outer Bearing... view full answer...
To replace just the brake pads that come on the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4,400 lbs # K23-478-479 you need the Replacement 10" x 2-1/4" Kit # K71-698-00 for the left-hand side and Kit # K71-699-00 for the right-hand side. I confirmed this with my contact at Dexter Axle
Attached is a review video for you to check out. view full answer...
You need to open the phone app for the Tire Linc OneControl TPMS w/ Signal Booster for RVs and Trailers # LC37VR and program what psi's you want it to send alerts for. It does not default at 80 psi like you mentioned. view full answer...
We do offer the Replacement Hardware Kit # 1091 and Replacement Foam Grip with Hardware # FP-1001-R which will allow you to replace the springs on your Lend-a-Hand Extra Large Folding Grab Handle # AM-533. Both kits include the bolts and springs which hold the handle to the mounting hardware. Currently the springs themselves are not available by themselves. view full answer...
The shank that comes with the Fastway e2 weight distribution systems rated for 1,000 lbs/10,000 lbs is part # FA92-02-4100.
This shank does use the industry standard 1-1/4" adjustments so if you're needing something a little longer or taller I'm linking our selection of replacement weight distribution shanks for you to filter through. view full answer...
To pick out bearings for a trailer hub you will need to remove one of the hubs so that you can remove the bearings and get the numbers off of them as we don't have a way to look up what a trailer uses based on brand.
Or, you can measure the spindle where the bearings ride so that we can pick you out the correct bearings that would fit the spindle. Or you can get me the axle diameter or brand and capacity. view full answer...
It looks like your 2020 Grand Design Transcend M-247BH has a GVWR of 6,995 lbs so your leaf springs should be rated for 3,500 lbs. If this is true then we have a few of these and you'll just need to select the correct one based off of the length of your current leaf springs (measured center-eye to center-eye):
23-1/8" - # e59SR
25-1/8" - # e68SR
27" - # SP-210275
If you lift your trailer so there isn't any weight on the springs you'll be able to measure the length of your leaf springs... view full answer...