The Replacement Gear Motor Assembly DSMX with P Connector for Lippert Slide-Out Item # LC368190 is the replacement for your 523725 slide out motor view full answer...
The direct replacement for your 2003 Fleetwood Bounder Motorhome gear motor assembly is the Replacement Gear Motor Assembly for Lippert Electric Slide-Out Item # LC386327.
I've attached a video that offers additional information about this part for you as well. view full answer...
It sounds like you have a Drive # 324-000002 RV camera system. If you want to replace the entire system you can order the # 324-000002 again. The rear camera alone is not available. If you have been satisfied with this system you can use it again, but a better choice is the Furrion # FOS05TASF system with 5" monitor screen. view full answer...
I found a couple options available for your 2008 Fleetwood Tioga Motorhome on the Ford Chassis. the fsn-21-9015 is the item number for the sticker used on many of the Firestone Ride-Rite systems. Both the replacement air bags are per bag so if you need both sides you will need 2 of the correct air bags.
To identify the correct replacement air bag you will need to identify if your air bag is mounted above the leaf spring like the Ride-Rite Air Helper Springs # F2153 are or if they are... view full answer...
The Jensen RV Stereo # JWM60A is a solid choice for a replacement stereo, but you will need to take some measurements to determine if this will fit as a replacement or not since we unfortunately don't have a way to know what came on your 2006 Fleetwood Discovery.
The overall dimensions of this stereo are 10-7/16" wide x 7" tall x 6-1/2" deep, but the mounting dimensions are 9" wide x 6" tall x 5-1/2" deep. The mounting dimensions are what you'll need to take note of because that's the... view full answer...
For your 2008 Fleetwood Southwind Motorhome I recommend the following replacement options:
Opti-Brite LED Dome Light - 11" Long x 4" Tall - 16 Diodes - Cool White
Item # ILL06COB
Opti-Brite LED RV Mini Dome Light - 354 Lumens - Rectangle - Neutral White - Clear Lens
Item # ILL07COB
Optronics RV Interior Double Dome Light with Switch - Incandescent - Rectangle - Clear Lens
Item # RVIL22
The Opti-Brite options are LED so they'll use less energy and last longer than incandescent bulbs... view full answer...
The correct replacement for your 524120 slide out motor is the Replacement Gear Motor Assembly for Lippert Slide-Out # LC27VR. I confirmed this with my contact at Lippert. view full answer...
I do believe you have a Kwikee Series 32 step with a curved linkage so you can replace the motor and linkage with the Motor Upgrade Kit for Kwikee Electric RV Steps # LC379145. This curved linkage is the "A" linkage that you've mentioned, so this is the complete kit needed to replace all of those components.
If you wanted to replace the entire step assembly with completely new parts you can use the Kwikee Electric RV Step Complete Assembly - Double - 32 Series - 24" Wide # LC372261. view full answer...
I do not ahve the abilty to pull an OEM build sheet for part numbers however, we have a couple options available. The Single Slide-Out Switch, # 37212285 is a 12V 40-amp continuous/momentary switch assembly. With cutout dimensions of 1.85" tall x 1.20" wide.
If you have a Lippert Components Slide-Out then I recommend the Lippert Hydraulic Interior Switch, # LC120639. view full answer...
I can certainly point you in the right direction. If both Ac units are original to your camper, it is safe to assume that they are both identical. To replace your Coleman Mach Air conditioners I recommend the Furrion Chill HE # FR82PV. This is a 13,500 BTU air conditioner. This one includes a conversion kit which will make it compatible with your existing Coleman systems. So you will not have to change out anything inside the camper. This will be a nice upgrade from an older Coleman unit.... view full answer...
For your Lippert Level Up Hydraulic Leveling System, you can use the:
-Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System # LC324269.
These replacement feet are 9" in diameter, and also includes the o-rings, the bolt, and washers.
Additionally, since you mentioned that your foot pads had become bent from use on soft surfaces I recommend also getting a set of snap pads:
-SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet # SP54FR4.
These... view full answer...
It's highly unlikely that you're going to be able to adapt or repair the damaged hose on your RV sewer maceration system, so you'll want to replace it with # SS25 which is a 25 foot extension and should provide you with plenty of hose length to run from your RV black water tank to the dump station. Different length hoses can be found with part number # 278-SS02 (10ft) or # SS15 (15ft).
In most cases, modifications are not recommended on parts for this reason, so if you can tell me more... view full answer...
For a replacement air conditioner, a 15,000 Btu capacity is as good as it gets. If you really want additional cooling beyond that you would be looking at adding an additional unit.
For a replacement for your Dometic, or for adding a new unit, I recommend the Furrion Chill HE Replacement RV Air Conditioner # FR42PV. This is compatible with your current Dometic setup so replacement will be fairly simple. It includes a start capacitor to help jump-start the AC and the rubber dampeners really... view full answer...
The correct replacement slide out motor for the Power Gear 524276 Motor on your 2006 Fleetwood Expedition is the Lippert Components RV Slide-Out Motor part # LC368193. view full answer...
Most of the time, the numbers molded into a trailer lamp lens are numbers that state that the lamp meets certain DOT regulations, and isn't necessarily an identifier for the lamp. However, the PM 108-15 number you found DOES indeed identify your existing lamp as a 106A from Peterson Manufacturing. Peterson has confirmed that the # 108-15A is indeed the correct replacement lens. You can confirm this for yourself by examining the lamp housing itself. Look for either a '106A' or a '108WA'... view full answer...
We have two options of replacement vent covers for the V2094 model, the white dome assembly, # BVD0449-A01, and the # BVD0449-A03 for smoke. I contacted the manufacturer to verify, there is not a metal lid option for the V2094. While we do carry a metal option, in # BV0534-00, it is for the model V2110 only. view full answer...
It sounds like you need 10" x 1-1/2" brake assemblies. The only replacement option is the Dexter Electric Trailer Brake Kit # K23-472-473-00. Assuming you have 3,000 lb axles, more than likely the inner bearing is # LM67048 and the outer bearing is # L44649. The correct grease seal would be the # RG06-050 (10-19). I recommend verifying this information to be sure. view full answer...
Typically you want to match the tires that are currently on the trailer. You can also look at the data plate on your trailer which probably lists the tire size. Outside of that there is no way to look up this information. I'm not sure which specific model you have, but I was able to find old pictures of a 2004 Fleetwood Prowler Lynx 722 data plate which lists ST175/80R13 tires.
Assuming this matches your current tires or the data plate, you could use the Karrier ST175/80R13 Radial Trailer... view full answer...
Although it's not from Petersen Manufacturing like the # 108-15A lens you'd looked at, Optronics makes an LED equivalent that we offer as part # MCL31AB for an amber lens or # MCL31RB for a red lens. Either lamp mounts on 3 inch centers, and is the same 4 x 2 size as the Petersen equivalents.
You can see a video showing a typical installation by clicking the provided link. view full answer...
I spoke with Lippert and the only correct replacement for a PowerGear Motor #1010000010 is the PowerGear RV Above Floor Slide-Out Motor Item # LC368417. view full answer...
Go To Results