You could use a E-Track Wood Beam Socket with the E-track setup that you have.
I spoke with my contact at Erickson and she went out and put a E-Track Wood Beam Socket # 59149 into an E-Track Trailer Cargo Control # E19148 and found that the # 59149 would not hang over the bottom of the E-track once installed and would work for your setup.
I attached a review video for the E-Track system for you to check out also. view full answer...
That's a fine question. Unlike many things in this world the companies like Kinedyne, Erickson and Cargo Smart all made the tracks the same size! So luckily for us we can use any of the e-track or x-track accessories like the Erickson E-Chock Wheel Chock for E-Track part # EM09162 interchangeably.
As a side note I really like X-Track or E-Track and find it to be extremely handy. Enjoy. view full answer...
It sounds like to me that you are wanting to attach shelves to the e-tracks in your box truck. If that is the case then what we have for this is the CargoSmart Shelf Track Brackets part # 3481726 which I think is what you are looking for but if it is not please just let me know. We also have pre-made shelves that fit into the e-track, the Brophy Utility Shelf for E-Track part # ETLSB and part # ETSSB or the CargoSmart Locking Cabinet for E-Track part # 3481725. view full answer...
Yes the e-track tie down anchors like the # 59131 can be installed in the Snap-Lock Horizontal and Vertical E-Track # SL27FR that you referenced. Basically any e-track accessory will fit in the # SL27FR that you referenced. view full answer...
For your Aluma 6810 HBT trailer, I recommend the Erickson Horizontal E-Track - Zinc Coated Steel - 2,000 lbs - 5' Long - Qty 1 # E19148 along with the E-Track Backing Plate - Zinc Plated Steel - 6" Long x 6" Wide # e96RR. This will save you the expense of the dual track and will allow you the flexibility of plates between the braces or around them.
This track also comes in 4 foot # EM19147, and 2 foot # EM59150. I recommend using the E-Track Plastic End Cap # ET8730 to finish your tracks.
For... view full answer...
The Brophy 5 Gallon Bucket Holder for E-Track # ETBHB that you referenced is designed to mount in vertical e-track like the # E19146. view full answer...
E-track can be driven over and it will be fine. It would not collapse or otherwise damage itself. You could use and drive over the Erickson Horizontal E-Track # EM19147. Then for a wheel strap the Erickson E-Track Wheel Tie-Down Strap with Roller Idler and Ratchet # EM58523 would work well. I attached a picture of a wheel and tire secured to this track for more info as well. view full answer...
For your E-track connections, I believe you are looking for the Snap-Loc E-Track Fitting with 5/16" Diameter Hole - 1,467 lbs # SLAEAFI or the Erickson E-Track Tie Down Ring - 2,000 lbs # 59147. These will work with J style tie-downs. We also have the Erickson E-Track Tie-Off w/ D-Ring - 2" Wide x 8-1/4" Long - 1,200 lbs # E59143. We also have tie downs with the e-track anchors integrated. I've linked the page to those options.
If this isn't what you are looking for, please give me... view full answer...
With cargo like your two classic Harleys you will want to make sure they are really well secured to prevent any damage. I recommend securing the E-Tracks to something more stable than just wood. If you are attaching the tracks to the floor I recommend you make sure they are secured either to the metal structure of the trailer or use metal plates like the E-Track Backing Plate, part # e96RR, to make it as secure as possible.
If the interior floor and walls are 7 ft long I recommend 5... view full answer...
I have found the galvanized coating on the etrailer Horizontal E-Track # e95VR will hold up to rust and corrosion better than the zinc coated Erickson Horizontal E-Track # EM19147 that you were looking at.
The galvanizing process leaves a thicker coating as compared to zinc coatings. This will allow for it not to wear off as quickly.
I recommend using the Erickson E-Track Tie-Down Kit # EM58523-09162-4 for securing your vehicles when using the E-Track. This kit will give you 2 wheel... view full answer...
If it were my trailer I would fasten the E-Track to the support beams under the trailer, either the side to side one or front to back ones, by going all the way through those support beams. E-Track like # E19148 is zinc-coated steel and since the trailer is aluminum you would want to paint the bottom of the E-Track. Otherwise the dissimilar metals can cause corrosion to start.
Be sure to also consider the fasteners used. Zinc-coated fasteners could be used but you will want to spray some... view full answer...
The break strength of the CargoSmart Horizontal or Vertical X-Track # 3481787 is 2,000 lbs which E-track on the other hand has a break strength of 6,000 lbs like the part # E19148. Working load limit for the E-track is 2,000 lb.
The longer sections like the part # 3481788 have the same capacity as the shorter sections as well. view full answer...
The E-Track part # E19148 that you referenced is not designed for a recess mount although if you wanted to come up with a way to do that you certainly could.
There aren't specific instructions for flush mounting E-track such as # E19148 but as long as the openings on top are clear and there is space enough below the holes to insert/remove accessories then it can be flush mounted or recessed some. It is pretty versatile stuff.
I attached a picture of the track installed as well as an install... view full answer...
Since you are wanting the most rust proof E-Track I recommend the etrailer Horizontal E-Track - Galvanized Steel - 2,000 lbs - 4' Long # e95VR as its galvanized finish will be the best for rust prevention, and will hold up fine even though you live near the ocean.
If you are mounting the E-Track to the floor of your Toy Hauler I also recommend the etrailer E-Track Backing Plates w/ Hardware - Galvanized Steel - 6" Long x 6" Wide - Qty 3 # e46RR unless you are able to get the E-Track secured... view full answer...
E-track offers a wood beam socket part # 59149 which can fit in the vertical E-track part # E19146 that you referenced. This would be perfect for creating a second floor/deck in the trailer.
I attached an install video for you to check out as well. view full answer...
Your plan of having an e-track like the part # E19148 attached to two different floor boards in your trailer would be perfect. This will distribute any weight on the e-track to two boards which is a sturdier way to go about it. view full answer...
Securing the Erickson E-Track # E19148 to 3/4 inch plywood should be sufficient.
To secure the track to the plywood, you can use screws, or rivets. Using 1/2 inch screws would be a good length with 3/4 inch plywood. You will want to attach screws at least every other mounting hole.
For tie downs and straps I would recommend either the E-Track Tie-Off Ring # 59131, or E-Track 2 inch D-Ring, part # E59143. Also available is the Erickson E-Track Strap with Ratchet, part # EM59136. view full answer...
The Erickson E-Track is very versatile so they isn't a specific size or model for your 5 x 8 Haulmark Transport Deluxe Cargo Trailer, just install as much or as little as you want, on the deck or on the wall. I have included a link to all of the E-Track tracks, as well as the accessories, for you.
If this were my trailer, in order to accommodate a variety of different loads, I would install 2 of the 5 ft Long Horizontal E-Track, # E19148, on the deck of the trailer and 4 of the 4 ft Vertical... view full answer...
In order to install a set of e-tracks like the Erickson Horizontal E-Track part # E19148 on a trailer with expanded metal floor you would need to install several backing plates like the E-Track Backing Plate part # BPEZ under the floor for support. The number of backing plates needed will vary depending on the length of the e-track and the amount of weight you have secured to it so you will just need to use your best judgement.
I have attached a list of different e-track lengths for you... view full answer...
Yes, the backing plate part # BPEZ is compatible with the PowerTye E-Track that you mentioned. They are made to the same dimensions as what the # BPEZ is designed to fit. view full answer...
Go To Results