Expert Answers about Livin Lite

• License Plate Screws to Use with Fastener Caps for License Plates Diamond Bling
• We do have the Mounting Hardware and Snap Caps # CR80430 which is a compatible size with the fastener caps you mentioned. The Cruiser Bling Fastener Caps # CR82730 that you referenced were designed to be a universal as possible but they require that the screw heads be less than 7/16 inches in diameter. Basically the caps that are included install behind the screw head and then the cover attaches to the caps which provides a friction fit.
  view full answer...


• Is Lomax Tonneau Cover # AB1010019 Pry Bar Proof
• With enough time and opportunity a thief with a pry bar could remove just about any tonneau cover. Or if they wanted to they could knock out a window of the truck with the same pry bar and steal things from the cab too. I wish I could tell you the Lomax Hard Tonneau Cover # AB1010019 was pry bar proof but none of the covers are going to be that secure. They just would make it very difficult for the casual thief and since they wouldn't know what's in the bed of the truck they'd be less tempted.
  view full answer...


• Is Gooseneck Hitch Ball of Ford Factory Rail Kit Compatible with Reese Goose Box
• Yes, the hitch ball you have that fits the factory Ford rail kit in your F-350 is compatible with the Reese goose box pin box adapters like the part # RP85FR that you referenced.
  view full answer...


• Could 2007 FJ Cruiser Tow 2016 Honda CR-V on Tow Dolly
• You'd be near the towing capacity of the 2007 FJ Cruiser but it looks to be possible. The FJ has a towing capacity of 5,000 lbs and the most your CR-V would weigh is 3,600 lbs so you'd be fine. For a tow dolly we have the Demco Kar Kaddy part # DM9713045 which has a self contained braking system and a steering axle so it will work great. It weighs 795 lbs so you'd still be under capacity.
  view full answer...


• Valve Stem Extensions on 2013 Sprinter 3500 RV
• I looked up pictures of your 2013 Via RV Sprinter 3500 wheels and the Wheel Masters Tire Pressure Valve Extenders # WM8029 that you referenced would be a great choice. These are 45 degree bent and aren't too long so they'd make access to the valve stems easier without being overly long.
  view full answer...


• Trailer Hitch Recommendation for 2014 Volkswagen Tiguan that Does Not Require Strap for Bike Rack
• So the easiest hitch solution for your 2014 Volkswagen Tiguan is going to be a hitch that does not require the stabilizer strap when carrying a bike rack like the etrailer part # e98906. Curt requires the use of their stabilizer strap part # 18050 when using their hitch to carry a non-supported load like a bike rack. I attached a review video for you to check for the strap as well. This is basically a precaution they require to help take some of the shock out of the hitch when on the road.
  view full answer...


• Replacement Tarp Recommendation for 2003 GMC Sierra with 6.5 ft Bed and Truxedo Lo Pro QT
• The replacement tonneau cover tarp you need is actually part # TX1117651 since the Lo Pro QT tonneau you have on your 2003 GMC Sierra 1500 with a 6.5 bed is part # TX581101.
  view full answer...


• Replacement Jack Legs for Venture Landing Gear VMC900R
• If you are in need of a replacement lead leg for your Venture vmc900r you'd want the part # LG-177202 or for a follow leg part # LG-177201. The lead leg is the one you'd attach the crank handle to and the follow leg is the leg that is opposite of that one.
  view full answer...


• Draw-Tite or Curt Trailer Hitch for 2015 VW Golf SportWagen TDI
• The Draw-Tite Class I Trailer Hitch # 24949 weighs 20-1/4 pounds and the Curt # C11422 weighs just a tad more at 22 pounds. Both Class I hitches are confirmed to fit your 2015 VW Golf SportWagen TDI and they feature just about identical dimensions and brackets so they will install the same on your vehicle. Both will have about a 2 inch hitch pin hole to bumper clearance measurement and a 14-1/2 inch ground clearance dimension when mounted. Both have the same 2,000 pound towing and 200...
  view full answer...


• Determining if Lippert Underchassis Double Bin Storage Unit Will Fit Keystone Outback Trailer
• The Lippert Underchassis Double Bin Storage Unit # LC175180 that you referenced is more of a universal item so it's not something that is designed or confirmed to fit particular trailer models. In order to determine if this will work on your Keystone Outback you will just need to take a couple measurements under the frame. First just make sure that you have enough room beneath the frame to accommodate the storage unit's overall dimensions of 96 inches long, 19-9/16 inches wide, and 8-1/4...
  view full answer...


• Replacing 4.80x12 Tires on Harbor Freight Trailer with Tires that have Better Highway Rating
• The Kenda Loadstar ST175/80D13 Bias Trailer Tire # AM3S120 that you referenced is going to close that trailer frame to tire gap by almost a full inch. This would put the new tire much too close to the frame on your Harbor Freight Trailer. The issue is that the existing 1 inch clearance between your trailer and tire side wall is already as close as I recommend having. Any wider of a tire and you are risking contact with the trailer frame because you still have to allow for some flex on...
  view full answer...


• Recommendation for Charging 6V Batteries
• We do have chargers available that are designed specifically for 6V batteries, of which I highly recommend the NOCO Genius UltraSafe # 329-G4. This particular unit can charge up to four 6V batteries rated for up to 40 amp-hours at the same time. It features multiple charging modes depending on your application and you don't have to worry about over-charging the batteries because of its integrated algorithm that actually analyzes the battery's condition. The amount of time it would take...
  view full answer...


• Can Spindle Grease Seal Set # BB60010 Work on E-Z Lube Spindle
• Yes, as long as your existing hub uses the # L68149 inner bearing and the included grease seal matches the dimensions on your current unit (1.875 inch inner diameter and 2.360 inch outer diameter) the Spindle Grease Seal Set # BB60010 will work great on your E-Z Lube Spindle. You do not have to have a Bearing Buddy in place for this to fit and work well. It will provide you with a smooth operating grease seal system in conjunction with the integrated grease zerks on your spindles. I have...
  view full answer...


• Is There a Speed Limit When Using the Rhino-Rack Fishing Rod Carrier # RR576F
• There isn't a speed limit with the Rhino-Rack Fishing Rod Carrier # RR576F that you referenced. Going highway speeds would not be an issue. The front of your vehicle as well as the windshield directs most of the high winds high enough over the top of your vehicle roof so rods carried in a carrier like this wouldn't be getting subjected to as high of winds as you might think.
  view full answer...


• Recommended 5th Wheel Hitch for a 2016 GMC Sierra 2500 with a 6-1/2 Bed
• Since your 2016 GMC Sierra 2500 has a short bed you need to use a sliding 5th wheel hitch. With a sliding 5th wheel hitch you don't need to worry about using an extended pin box as the hitch will slide back far enough for you to have proper trailer-to-cab clearance for tight turning situations. I recommend using the B&W Companion 5th wheel hitch because it is rated for 20,000 lbs, features a cam-action latching handle that keeps the dual jaws from binding which makes it much easier to...
  view full answer...


• Availability of Replacement Lift Motor for Older 2000TRS Fan-Tastic Vent
• I reached out to my contact at Fan-Tastic Vent (now owned by Dometic) and she said that for your older model assembly there unfortunately is no longer a replacement lift motor available that will be compatible. Your best option at this point is to replace the entire unit. Due to the age of your assembly if anything else were to go wrong those replacement parts would be just as difficult to find. I recommend taking a look at the Fan-Tastic Vent Roof Vent # FV807350. This will fit your...
  view full answer...


• Roof Rack for 2019 Jeep Grand Cherokee without E Group Flush Rails
• Thule used to have a fit for your style of non-E-group roof rails but at this time they do not have anything. Best option we have is the Rhino Rack Aero Bar roof rack part numbers # RRVA137B-2, # RRRLKVA, and # DK234 which fits to the outsides of your flush rails more like a naked roof fit.
  view full answer...


• Install Harness Needed for Prodigy P3 Brake Controller in 2019 Ram 1500
• The correct install harness to install a Prodigy P3 part # 90195 is going to be the part # 3024-P for your 2019 Ram 1500. The port on your truck that you need to find is at the rear of the center console area just under the temperature control knobs as you can see in the attached picture.
  view full answer...


• How to Reduce Chucking When Towing 2019 Keystone Fusion with Lippert 1116 Pin Box
• For the Lippert 1116 pin box replacement the best cushioned option is the Trailair part # LC155943. This system uses an air bag and shock to cushion and dampen the movement of the pin box which will do a great job smoothing out your ride quality. Another really big factor with fifth wheel chucking is the fifth wheel hitch jaw system. If you have a hitch that allows a lot of movement in the hitch jaws then that's where most of the chucking is coming from. You'd want a hitch that has a...
  view full answer...


• Could Valterra Keyed Entry Door Knob # L32CS000 Fit 1995 Jayco Eagle 12
• You'll need to measure your door to know for sure if the Valterra Keyed Entry Door Knob # L32CS000 you referenced would work but most likely it would since it was designed to fit the standard RV door dimensions. This is designed to fit 1-3/8" to 1-5/8" thick RV doors with 2-3/8" to 2-3/4" from center of face hole to leading edge of door.
  view full answer...