I have attached for you below all the parts you requested for your 2019 Grand Design Reflections 303RLS.
5-Leaf Double-Eye Spring part # e34SR
MORryde Suspension Upgrade Kit for Tandem Axle Trailers part # MR46ZR
MORryde Shock Absorbing Suspension Equalizers part # MR27ZR
MORryde U-Bolts for 5,200-lb to 7,000-lb Round Trailer Axles part # MR66ZR
I know you said you wanted to use the Dexter EZ Flex but the MORryde CRE300 are much better as they offer more travel which equals better shock... view full answer...
The slide out rollers need to be wound 7 full times when they are installed. So if you were to remove yours to replace the head with the # LC34FR you'd need to wind the roller 7 full times. view full answer...
For your 2019 Grand Design Reflection 337RLS I recommend the Kodiak Disc Brake Kit # K2HR526D. This uses the same 6 on 5-1/2" bolt pattern for your current wheels and has a Dacromet coating to prevent corrosion. You will need 2 of these kits for both your axles along with 2 of the Bearing Kits # DBRKHW6EZ.
I recommend using the Hydrastar Vented Marine Electric Over Hydraulic Actuator # HS481-8067 as it allows for a simpler plug and play installation of the components. Then you will be... view full answer...
The hose and fittings sizes are standardized for RV's. Therefore, what you have is going to be a type 1 to either a 1/4" NPT or 1/4" Male Inverter Flare. If you have the former I recommend part # 100473-12 or part # 37207-30715 if you have the latter. That said, I get why you're confused as these fittings don't actually mic out to 1/4", they will measure larger but that does not correlate to their nominal size which would be the same for measuring any sort of NPT fitting. view full answer...
You can upgrade your Dometic awning to a Solera power awning with the part # LC434724. This will replace the arms of what you have now but allow you to keep using the awning fabric. view full answer...
I would be happy to help you determine the correct replacement leaf springs for your 2016 Grand Design Reflection 29RS with tandem Lippert 4400lb axles, but unfortunately the axle tags like the one shown in your picture do not have leaf spring information and neither does Lippert as the springs are put on by the RV manufacturer.
Instead you will need to measure your current springs from center of spring eye to center of spring eye. You will also need to make sure the trailer is jacked... view full answer...
While we don't have an enclosure for the replacement Furrion Vision S camera part # FCN48TASF the best solution might be to come up with a shroud that could install over the camera to allow it to be protected by the weather. An enclosure would probably obstruct the viewing angle and reception but just a shroud that covers the top of the camera would probably do the best job. view full answer...
For the MaxxAir MaxxFan Mini Roof Vent, # MA00-04301M, I suggest the MaxxAir FanMate RV and Trailer Roof Vent Cover, # MA00-955001 for white or # MA00-955003 for smoke or, # MA00-955002 for black. This is designed specifically to fit 2015 and newer MaxxFan and MaxxFan Plus roof vents with mounting tabs and for use with high-powered fans.
Don't forget the Bug Screen for MaxxAir FanMate Roof Vent Covers, # MA00-955203 (smoke) and # MA00-955202 (black).
Please note the linked product... view full answer...
The 12 MTI or the 6 MTI that you are seeing on trailer hubs like the # 8-201-9UC3-EZ that you referenced is not related to the part number or fit so it wouldn't be something you'd need to match. If you see 8-201 on your hub and/or it's a 6k trailer axle then this for sure is the correct fit for you. view full answer...
The bearing kit # BK3-210 that you mentioned is specifically for 7,000lb axles.
For your 2020 Grand Design Reflection 320MKS fifth wheel with Dexter 6,000lb axles, the correct bearing kit will be either # BK3-100 or # BK3-110.
# BK3-100 uses a seal with an ID of 2.250", whereas the # BK3-110 uses a seal with an ID of 2.125".
You may need to measure your seal using a tool such as the 4" Carbon Fiber Digital Caliper # PTW80157 in order to correctly match up your bearing kit.
I have included... view full answer...
I have another option, but unfortunately none of the cargo carrier bike rack combos are rated for use on a 5th wheel trailer like your 2021 Grand Design Reflection.
Instead I recommend using a front mount trailer hitch receiver on your truck with the 17x46 Curt Cargo Carrier for 1-1/4" and 2" Hitches # C18145 to carry your 100lb generator. This cargo carrier weighs in at 28lbs, and has a 500lb weight capacity making it plenty strong to carry your generator. You will want to make sure you... view full answer...
Since your 2020 Grand Design Reflections was pre-wired for a Dometic brand AC setup the best recommendation is going to be the Advent Air AC Unit for Dometic setups part # ACDOM150B. This is a higher BTU unit that will plug right into the pre-wiring of your RV which means your current Dometic thermostat will control it without any modification. This also comes with a start capacitor which will ease the power draw on initial start up of the unit which helps with power management. view full answer...
For you slide of 111" or 110" use the Solera RV Slide-Out Awning part # LCV000251461 for black or part # LCV000163292 for white.
On the 102" use the Solera RV Slide-Out Awning part # LCV000168108 for black or part # LCV000163290 for white view full answer...
The correct bearing kit you'll need for your 2018 Grand Design Reflection 303RLS would be the part # BK3-200 since we know your trailer has 7k axles. To pick out the correct leaf spring though I would need to know what the length of your current spring is. view full answer...
MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part # MR33WR. This is the MORryde part number XF12-001. view full answer...
Most likely one of the leg components is bent and is being prevented from moving because of that. You might be able to get lucky and you'll be able to bend it back if its not too bad but otherwise you'd have to replace it with it another # LC298707. view full answer...
Thanks for the info you mentioned, based on that the correct bearing kit for your Lippert 5,200 lb axle would be the part # BK3-300. view full answer...
I'm assuming you have adapter rails like # C29BR in your Ram 2500 puck system which are industry standard rails. If that is the case then yes, you can install the Curt A16 # C16521 on the same rails. You can also swap out the head. The Curt R16 # C16560 is the base for both the E16 and A16. The A16 replacement head is the # C16520 and you will also need the head mounting hardware # C35UR. view full answer...
If your 2018 Grand Design Reflection happened to have a Fastway breakaway kit installed on it yes the replacement plunger pin # FA80-01-2206 would be correct replacement but we have no way to verify that. I do have an easy solution that would for sure work though. Since all of the breakaway systems operate the same way they are universal so you could just replace the entire switch with the part # 3802348 and you'd be set. view full answer...
The Torklift # TLA8003 (3 Steps) will fit for your trailer. These are intended for a mounting bracket measuring 27-1/2" and an entry height of 25-1/2" to 36". Alternatively, the Torklift # TLA8004 (4 Steps) is designed for an entry height of 32-1/2" to 44" and will extend out further.
If you have trouble on steps I would recommend the 4-step model, just know that they extend out further, otherwise the 3-step model is fine.
Also check out the Torklift # TLA7621 Hand rail. 4 steps is... view full answer...
Go To Results