I have a solution for you.
After talking with my contact at RV Snap Pad and researching this foot pad you have. They do not make a snap on pad that fits this type of application.
The lips on your foot are to tall and they do not have anything that can fit on them.
You will need to go with a stabilizer pad like the Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2 # SC57VR. view full answer...
For your 9-inch Lippert jack feet, I recommend the Stromberg Carlson RV Jack Pads for 9" Round Jack Feet # SC49MR. It comes with 6 pads and works to fit the contours of your Lippert feet. The pads include built-in drains that release moisture and prevent your jack feet from corroding. view full answer...
For your jack pads, I recommend the Lippert Components 5th Wheel RV Landing Gear Foot Pad - 9" Round # LC314667. Then you can use the SnapPad Jack Pads for 5th Wheel Campers w/ 9" Round Jack Feet - Qty 4 # SP54FR4. view full answer...
Your Anderson Jack Block should technically "fit" in the SnapPad XTRA XL Jack Pads # SP74FR4, but since these are designed around the Lippert landing gear feet I can't guarantee the SnapPads will actually fit snug around the bottom of the jack block so I don't recommend going this route.
Instead, I recommend checking out the Stromberg Carlson RV Jack Pads # SC57VR which measure 14" x 12" and will give you more traction and stability than you already have. view full answer...
Depending on which Lippert leveling system you have it is possible that you need either the SnapPad Jack Stand Pads for 5th Wheel and Class A Motorhome - 9" Round Jack Feet part # SP54FR or the Replacement Pad for SnapPad Jack Stand Pad System - 8" Round part # SP34FR.
To ensure you get the perfect fit please measure your foot plate on you system and choose the one that matches up. view full answer...
Yes, the Jack Foot Pad, # LC314667, will work on your Keystone Impact as this product will fit Lippert landing gear like what would be on your RV. view full answer...
Yes we do offer the SnapPad Jack Pads for Class A and C Motorhomes w/ 9" Round Jack Feet # SP54FR4 in a 6 pack with the part # SP54FR6. view full answer...
For your Lippert Ground Control 3.0 Electric 5th Wheel Leveling System # LC358590, you would want the Lippert Components 5th Wheel RV Land Gear Foot Pad # LC314667 for a replacement.
We spoke with my contact at Lippert and he confirmed that these pads will work with the Ground Control system as long as your leveling leg has a hole in the end of the leg to slip the pin though to secure the foot pad.
The # LC314667 comes with 2 foot pads that each measure 9 inches in diameter. view full answer...
Since the landing gear feet of your 2019 Holiday Rambler Navigator 37R are 10 inches and round the correct set of SnapPads would be the part # SP64FR74 that you referenced. view full answer...
Yes, the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 6" Square Jack Feet - Qty 4 # SN99FR will work for you.
Install temp is not a huge issue, takes a few minutes per pad. The pads will maintain structural integrity down to -40 degrees and up to 120F degrees. It is suggested that install will be easier if temps are over 50 degrees.
SnapPad installation should be performed on a level or near level surface preferably a hard surface like concrete or asphalt. Wheel chocks should... view full answer...
The SnapPad Jack Stand Pads for Motorhome part # SP84FR4 are designed for 10" Octagon foot plates. This kit includes the four you're looking for. view full answer...
They certainly will! Each jack included with the # UF48-979003 has a 6000 lb capacity, and is meant to stabilize a trailer (not lift it). These work really well to prevent the fore/aft and back and forth rocking experienced while walking around in a trailer. Be sure that the pad is in contact with the frame of the trailer when the jacks are deployed. view full answer...
Yes, the Jack Foot Pad, # LC314667, will work on your 2010 Keystone Montana as this product will fit Lippert landing gear like what would be on your RV. view full answer...
The measurement to determine the correct JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs is taken from directly under the cab of the trailer in between the two outer tubes on the jack (inside to inside). I have attached a photo of this for you as well.
If this distance is less than 58" then you will want to use part # LC191024 but if it is more than 58" and not 66" then you will want to use part # LC191023. Since you have hydraulic jacks in the rear you will also need one set of... view full answer...
If your 2018 Fleetwood Flair 30 has 9 inch round jack feet then the correct SnapPad Jack Pads is part # SP54FR4. We don't have ability to look up what your RV has so if you run out and measure your feet and find they are 9 inches round this would be correct. If you have something different let me know and I'll help you pick out what you'd need. view full answer...
The best option we have for you would be to use a standard a-frame jack with a wheel. If you do not have a wheel then you can most likely add one using part # BD500245 as they are fairly universal. However, a wheel will reduce the capacity of the jack to 1,200 lbs.
We do have trailer dollies with a drive system like the Trailer Valet XL Trailer Dolly part # TVXL25 but they cannot be pulled by a winch and have a maximum incline rating of 7-10 degrees. view full answer...
The Leveling Scissor Jack part # JSC-30 should work well on your motorhome named, "Dottie."
The extended height is 30 inches so as long as the trailer is less than 30 inches from the ground these should work well. view full answer...
I do have an option for you but the Ultra-Fab Footplate for Landing Gear and Stabilizer Jacks part # UF17-940006 are made for landing gear legs, not scissor jacks. That said, they don't really make anything that would increase the surface area of the foot on a scissor jack so if this is what you need you would have to look at separate blocks such as the Stackers Leveling Blocks for Trailers part # A10-0916 for a quantity of four or part # A10-0917 for a quantity of one. view full answer...
The Replacement Front Foot Pad for Lippert Components Ground Control part # LC362486 is made specifically for the Lippert Components Ground Control 3.0 Leveling System which it does not sound like you have based on you saying you have rectangular foot pads now. That said, the Lippert Components 5th Wheel RV Landing Gear Foot Pad part # LC314667 would be a much better option because it has the wider footprint you are after and it will work with most power landing gear systems so it should... view full answer...
The Lippert Components 5th Wheel RV Landing Gear Foot Pad - 9" Round # LC314667 is the original part for the Ground Control 2.0 system like you mentioned, but the Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System # LC362486 will work if your square jacks will fit the 2 inch square measurement on this foot (see picture). I've attached a video with more info for you to check out as well. view full answer...