You will have no problem using your Curt Echo Wireless Brake Controller item # C51180 when you lose cell signal. The wireless functions are controlled by Bluetooth. Bluetooth does not require a carrier signal or Wi-Fi to function. view full answer...
The purple wire on the Replacement Control Module for Lippert Electric Coach Step # LC301702 is intended to connect to the positive power wire for the coach's porch light, so it comes on when the step is activated. Unfortunately neither I nor my contact at Lippert has any way to look up that wire color for your 2011 Tiffin Allegro.
If you have a circuit tester like # PTW2992 you can try testing the wires on the coach until you find the one that delivers power to the porch light.
In a... view full answer...
What you can do is get the TireMinder i10 TPMS for RVs - LCD Monitor - Signal Booster - 4 External Tire Sensors # TM89FR and then also order 3 of the part # TM-2ALUM which comes with 2 of the aluminum tire sensors. This will give you the 6 aluminum plus 4 brass sensors you need for your application. view full answer...
The Hot Dot LED Trailer Clearance and Side Marker Light # 328-003-17R does not require a gasket or base plate to mount it on your trailer. This light will mount to the surface of your trailer as is. view full answer...
On the MB Sturgis Sturgi-Stay T-Fitting for POL Valve part # 103537-MBS it does provide two connection points for accessories to be used. I see the confusion in the wording though. It will connect directly between the on board propane tank and the gas lines on your RV. You can then attach your fire pit and grill and have what sounds like a heck of a time in a very nice coach! view full answer...
To install the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 on your 2013 Tiffin Allegro Bus you will need to hardwire it in as there is not a port that allows it to plug in.
We have previously confirmed with Tiffin that there will be four wires under your driver's side dash that have butt conectors on them, and you will use these to wire in the Prodigy brake controller. The wires from the Prodigy are going to be Black for power, Blue for brake controller output, Red for stop light... view full answer...
The correct Roadmaster Reflex Steering Stabilizer with Mounting Brackets for a 2019 Ford F-53 Chassis is part # RM-RBK25-RSSA. In regards to installation, the Custom Mounting Brackets install on the driver side of the front axle. view full answer...
Later model Jeep's such as yours do not have locking steering wheels which is typically why when flat towing one will leave in the ACC position. However, you will want to refer to your vehicle specific owners manual for placing your specific Jeep model in proper arrangement for flat towing. Look under "Recreational Towing" section and follow the manufacturer's directions for manual or automatic transmission whichever you have.
If you do not already have a battery charge line from your... view full answer...
This is partially correct. The Demco Stay-IN-Play Duo Supplemental Braking System w/ Wireless Coachlink Monitor - Proportional # DM86VR installs in your tow vehicle and not in the coach, however it's not compatible with air brakes. Instead of the Stay-IN-Play, you'll want to use the Demco SBS Air Force One system # DM26VR. It will work very similarly and provide proportional braking for your tow vehicle, in a permanently installed braking system.
The wireless CoachLink sends a signal to... view full answer...
The SumoSprings Maxim Custom Helper Springs - Rear Axle # SSR-183-54-1 can be installed without removing the wheels on your 2014 Tiffin Allegro Open Road 36LA, but it will be more complicated because of restriction working room. I've attached a video to show you the installation which will require mounting the upper bracket to the frame which will require drilling a few holes.
It is possible to install without removing the wheel, but having the equipment for drilling holes in close proximity... view full answer...
The Replacement Lens for Gustafson 3" Recessed RV Puck Light part # 277-000393 is made of plastic, not glass and it features a press-in installation. view full answer...
Yes the Motor Upgrade Kit for Kwikee Electric RV Steps Item # LC379145 that you referenced would cover everything and would get your Series 32 steps working again as it covers all of the mechanical and electrical components. view full answer...
The green wire of the 4-way connector you sent in a picture of is the right turn/stop circuit, the yellow is left turn/stop, brown is running light, and white is ground. You could use the # 18252 to easily splice into the circuits as well to make an additional connector. view full answer...
The Adco SFS AquaShed Cover for Class A RV part # 290-52206 comes with four weighted straps as you mentioned. These straps are designed to help secure the bottom side of the cover to the motorhome. In order to install them you will first need to locate a lower strap on the cover and then attach one side of weighted strap to this. Once this is done you can then toss the other side of the weighted strap under the motorhome and secure it the strap on the other side of the cover.
I have attached... view full answer...
The Lippert Components RV Slide-Out Motor by Klauber # LC130057 does have the electric brake on it that does act like a clutch to keep you from over-extending or over-retracting the slide and causing any damage to the motor or frame. I'm not sure what you mean about the 1/2 inch, as the motor will draw the slide out in tight and will also fully extend the slide out so you have full intended movement. I contacted the manufacturer to confirm this. view full answer...
It's tough to say exactly what you're doing wrong here, because with bayonet style light bulb bases you should simply line up the pins, push the bulb in and twist clockwise to install new bulbs- which seems to be the process you're following.
If the pins aren't catching a slot and allowing you to twist you may just not be pushing hard enough; I know we just changed out some LED lights on a fixture in our house and it really did seem like we weren't going to get them to fit. Ultimately... view full answer...
You are correct about the Tekonsha Prodigy RF Wireless Trailer Brake Controller part # TK94FR in that all you will need is 12 volt power on the 7-way. Unfortunately, there is not easy way to go back and forth between a 4-way and 7-way trailer connector on the trailer side at least. However, you can go back and forth between a 4-way and 7-way trailer connector on the vehicle side and for that I recommend the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185.
The only thing you will need... view full answer...
The Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK6-RSSA is not the correct fit for your 2018 Tiffin V-10 Motorhome. The # RM-RBK25-RSSA is the correct fit and will correct your fit issue so you will just need the Custom Mounting Brackets for Roadmaster Reflex Steering Stabilizer # RM-RBK25. view full answer...
Since Hughes Autoformers does not have a version of the Hughes Autoformer Voltage Booster with Surge Protection # HU57FR that was setup for hardwiring you'd have to drill out the rivets on top of the unit to remove the lid so that you could access the wiring that leads to the connectors on either side for wiring it. view full answer...
The range of the Curt Echo Mobile Brake Controller part # C51180 is 50 feet so since you wouldn't be exceeding that range it would work fine for you. It would not require a wifi extender. view full answer...