The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 you were looking at measures 34-1/2" between the sides of the hitch which you can see in the included diagram.
This hitch may fit with your Tommy Lift, but you will need to compare the measurements shown in the diagram to your vehicle with the Timmy Lift to see if you will have enough clearance.
I included a video of the # 3371809055 for you to take a look at. view full answer...
You are correct, the URMDH - Rear Suspension Enhancement System with Aeon Hollow Rubber Springs by Timbren is the same as the # TURMDH Timbren Suspension Enhancement System - Rear Axle.
According to Timbren, this suspension enhancement system is a confirmed fit for all 2021 Isuzu NPR-HD models. view full answer...
Finding the cold side of the brake switch can be a little difficult, but not overly so. First, you want to be using a voltmeter or a circuit tester, like the # PTW2993. As this is the cold side, there should be absolutely no power running through the wire until the brake pedal is depressed. This would be the wire you will need to splice the red wire from a controller, like the Curt Spectrum # C51170, together with.
Depending on how the vehicle is currently wired, you may need a few more... view full answer...
For your 2002 Isuzu NPR HD you're going to need to install a universal trailer hitch like the weld-on Draw-Tite # 41990-07 or perhaps the Buyer's Products # 3371801051 which is also a weld-on application but it has a 62" crossbeam as opposed to the 44" crossbeam for the Draw-Tite.
So basically we don't have a custom fit for your box truck but we do have some universal options available that you can check out. If you still aren't sure then I recommend speaking with whoever you plan on having... view full answer...
There are a few options that may fit your 2009 Isuzu NPR with a dump bed, but there are no options that are confirmed to fit.
The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 is designed to fit trucks with a 34" wide frame and will need to welded and bolted to the frame. This hitch plate has a 17000lb trailer weight rating, and the 2" receiver tube you were looking for.
Another possible option is the # 41990-16 as it has 16" tall brackets, fits... view full answer...
There may be a solution for you though the Traffic Cone Holder for E-Track or Rack'em Spare Tire Holder # RA-26 does not have a specific weight rating for one of the brackets.
There are a couple options for you to consider like the CargoSmart Rotating Board Holder for E-Track and X-Track Systems # 3481740, which will require you to provide your own shelving. I believe this may have been what you were referring to by something like the cone holder with the bar laying flat in the bracket.... view full answer...
All vehicles built after 1996 should have OBD II instead of the OBD ports, so your 2003 Isuzu N-Series will should almost certainly have an OBD II port. You'll be able to tell the difference because the OBD II has 16 pin holes where the OBD has 12. Your vehicle's owner's manual should also tell you whether or not your vehicle is OBD II compatible, if that is still available.
When it comes to choosing between the two, I really prefer the Edge CTS2 # EP84130 to the Edge CS # EP84030 because... view full answer...
Your 2016 Isuzu NPR will need a weld-on trailer hitch, and there are a couple of options from Draw-Tite, which is the same manufacturer as Reese hitches. Based on my research, a '16 NPR has a 33-1/2 inch chassis width, so you can choose from either of the following options, with the difference being their bracket height, depending on how much drop you need.
- 7" Tall Brackets: Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07
- 16" Tall Brackets: Draw-Tite Ultra Frame... view full answer...
Thank you for reaching out!
The suspension enhancement I recommend for your 2021 Isuzu N-Series truck is the SumoSprings Helper Springs which are available as part # SS58DR for the front axle and part # SS38DR for the rear axle.
I really like these because once they are installed you can literally forget about them as they require zero maintenance. These work to not only help level your vehicle, but they are help stabilize it when you're turning.
Attached is a review video for you to... view full answer...
Go To Results