According to TeraPump, the TeraPump Fuel Transfer Pump # TE54VR will work with high octane racing fuel. This is compatible with any non-corrosive liquid such as gas, non-potable water, kerosene, diesel or light oils. view full answer...
Yes, the TeraPump Fuel Transfer Pump for Gas Cans # TE34VR is compatible with diesel fuel. It will work with non-corrosive liquids, such as gasoline, diesel, DEF (AdBlue), non-potable water, kerosene, antifreeze, windshield washer fluid, mild detergents, agricultural chemicals, and light oils view full answer...
Yes, you can add a fuel meter to the TeraPump Fuel Transfer Pump for 55 Gallon Drums and IBC Totes # TE24VR. While we do not have a fuel meter available, you can source one from your local farm store.
Or to simplify things, we have the TeraPump Fuel Transfer Pump w/ Meter # TE96VR available. This pump will also work with 55 gallon drums, but has the meter already included. The only thing about this option being, that is is only 33-3/4" long versus the 49" length of the # TE24VR. So, you... view full answer...
Yes, you can use the TeraPump Plastic Rotary Fuel Transfer Pump for 15, 30, and 55 Gallon Drums # TE47VR with diesel fuel.
This pump is also compatible with water-based solutions of acid, alkalis and salt, water and all petroleum products (not gas), most organic acids, solvents, waxes, planting solution, detergents, and water-soluble inorganic chemicals. view full answer...
No, we do not have an alternate hose for the TeraPump Fuel Transfer Pump for Racing Utility Jugs # TE89VR that allows for a further reach or deeper jug. view full answer...
The venting of the Replacement Vented Cap for DeeZee Transfer Tanks # DZGASCAP3 is adequate that it would not need to get removed when pumping fuel with an electric pump like you mentioned. You could leave it on and you'd be fine. view full answer...
The TeraPump Ethanol Transfer Pump # TE59VR works with methanol, ethanol, DEF(AdBlue), liquid soda, window washer fluids (Especially made of Ethanol), brake cleaner & non-potable water. This pump should not be used for high octane racing fuel. For a pump that is compatible with high octane racing fuel you would need the # TE54VR. view full answer...
We do not carry the Flo-Fast cans. But from all of the information I could find on them, yes the TeraPump Fuel Transfer Pump for Racing Utility Jugs # TE89VR will work with the 15 gallon Flo-Fast can. view full answer...
Assuming you are not pumping diesel fuel and gravity feeding the fuel lines at the same time there should be no reason you can't use connector tee # DZ97960 in your transfer tank in your 2013 Ford Super Duty. view full answer...
DeeZee Connector Kit # DZ97960 is designed to make a gravity feed connection between an auxiliary diesel tank like # DZ91752X and your vehicle's diesel tank. This kit is not intended to connect the aux tank to your engine fuel line but to your standard diesel fuel tank.
There is no reason you could not add a suitable diesel fuel pump to the setup to speed up the flow from tank to tank, but since the auxiliary tank is usually much higher up than the vehicle tank the gravity flow usually... view full answer...
To power the 20 GPM 12V fuel pump from the 7-way you would need to power it from the vehicle's battery. To do that you would use Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End part # BDW20206 and connect the winch wiring to the positive and negative side of the vehicle's battery via a circuit breaker that is appropriate for the amperage of your fuel pump. If your fuel pump doesn't draw more than 40 amps you can use 40 Amp In-Line Circuit Breaker part # 9510 6" away from... view full answer...
If you want to release the pump mechanism of the TeraPump part # TE89VR so that the fuel in the lines can drain just unscrew the top white cap and the vacuum gets released allowing that to happen. view full answer...
Yes, the Light-Duty Toggle Switch # PK33300 is adequate for your 1947 Ford Coupe. When used with the 6 volt system you have the switch has a maximum capacity of 35 amps.
You can use either the Pollak Toggle Switch Rubber Half-Boot # PK25371 or Pollak Toggle Switch Rubber Boot # PK25370 if you prefer to hide the threaded portion of the switch. view full answer...
The Ultra-Fab Universal Access Door for Trailers and RVs # UF48-979009 is 5x5 inches so that would give you 7 inches on the diagonal. I can't find the gas pump handle dimensions online so I cannot confirm a fit for you. view full answer...
We offer several hitch options for the 2014 Jeep Patriot, all shown on the linked page, that install with certain requirements. These installation requirements may include some trimming of plastic fascia parts, temporary removal of the exhaust heat shield and/or tow hooks, and temporary lowering of the exhaust, just to provide easier access to the mounting points on the frame.
I have never heard of a hitch installation on a standard passenger vehicle being affected by the location of... view full answer...
To know if the Curt Custom Fifth Wheel Installation Kit, # C16418-204, will fit your 2005 Chevy 2500 long bed with the toolbox and spare fuel tank installed, you will have to check to see if there will be interference where your toolbox and spare fuel tank is located on your truck bed and where the installation kit rails will be installed in your truck bed to your frame rails.
The hitch center line on the Curt installation kit will sits 1-1/2 inches in front of the trucks axle center line.... view full answer...
We do carry the DeeZee Combo Auxiliary Tank # DZ92740X that has a Brite-Tread finish. This is a confirmed fit for your 2001 Dodge Ram Pickup whether it has a 6-1/2' or an 8' bed.
Unfortunately we do not have any deep tool box/tank combinations, but this is the best that we have to offer. If features a 43-gallon capacity transfer tank that has been tested and rated for diesel fuel as well as a toolbox. The overall measurements are 54" long x 18" deep x 17-3/4" tall.
If you have an 8' bed... view full answer...
The Demco Recon part # DM8550045 measures 28 inches front to back and 30.5 inches left to right. The center of the base of the Recon installs into the gooseneck ball hole in the truck. So you would need about 14 inches of clearance behind your gooseneck hole for the Demco Recon to fit in the truck. Your transfer tank needs to be 14 inches or more away from the gooseneck hole.
The L-shaped transfer fuel tanks we sell are 24 inches tall. You want to make sure the tank is not going to interfere... view full answer...
The TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLF2021 installs in line with the hinge edge of the fuel door on a 2022 F-250/F-350 so the turnbuckles would most likely prevent the door from fully opening, but should allow for enough room to open the door around 90 degrees and get the pump in.
If you use the front mounting hole when installing your turnbuckles # TLS9529-2-LK then you'll most likely be out of the way of the fuel door. view full answer...