I recommend looking at the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. This is a universal receiver you can use as there currently is not a custom fit receiver for your 1985 Itasca Sunflyer on a Chevrolet P30 chassis. This particular receiver can be welded or bolted to the frame and uses 7" tall brackets. We do have the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 that uses 16" long brackets depending on the amount of drop you need on the... view full answer...
Yes, as long as your RV has a 12 volt electrical system (it does), the Air Lift Compressor System part # AL25856 will fit and work well. view full answer...
Yes, the Air Lift AirLift 1000 Air Helper Springs for Coil Springs part # AL81560 is a confirmed fit for your 1985 Sport Coach Pathfinder which is on a Chevrolet P Series chassis. The shipping cost will be displayed upon checkout. view full answer...
In order to haul a generator on the front of your vehicle, I suggest using a front mount trailer hitch such as the # 13703. This is an adjustable type hitch that fits frames from 22" to 72" in width. It is not a custom fit but will require a little bit of fabrication and some welding. Curt states that all non-trailered loads need to be secured with Stabilizing Support Strap # 18050. After installation of adjustable hitch, you can use a cargo basket carrier such as the Curt Cargo Carrier... view full answer...
You are correct, the 1994 Chevrolet P-Series Chassis came with both two wheel drive front coil spring suspension and four wheel drive front leaf spring suspension setups. Fortunately, we have stabilizer and sway control options for both models.
For your coil spring suspension, I recommend using both a front steering stabilizer and rear axle stabilizer. For the front steering stabilizer, I recommend using the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Motor Homes... view full answer...
The ClearPlus 77 Series HD Windshield Wiper Blade - 26 inch # CP77261 will work on your 1992 Fleetwood Bounder Class A Motorhome. The wide saddle mount is the design that installs by using two screws. This wiper blade offers both the connectors for installation to the 1/2 inch to 5/8 inch wide saddle mount and the 12 x 4 J-hook.
This part number is for a quantity of one wiper blade view full answer...
No, the Roadmaster Rear Anti-Sway Bar # RM-1259-109 is not a confirmed fit for your P-Series Chassis. The only anti-sway bar that we carry for a P-Series Chassis like your 1995 Georgie Boy would be the Roadmaster Front Anti-Sway Bar and Bushing Kit # RM-1109-116. view full answer...
The motor is likely the culprit of your steps not retracting all the way. The nylon gear inside the motor is likely the part that is worn. The step is able to extend due to gravity but it sound like the motor does not have enough power on the upstroke to fully retract. Unfortunately, I am not able to reference the model number that you provided. However, if it is a Kwikee Step then there would not be any replacement parts for you due to the age of the step. Therefore, your only option would... view full answer...
According to Timbren's fitment guide the Timbren Front Suspension Enhancement System # TWFRW22 would be a compatible fit if your 1994 Chevy P32 chassis has a leaf spring suspension. If you have a coil spring suspension you would need the Timbren Front Suspension Enhancement System # TGMFP30W instead. view full answer...
I went ahead and reached out Lippert and they were able to tell me that the mounting screws on the Replacement 2-Quart Pump Reservoir Kit for Lippert Components Hydraulic Power Unit # LC46FR measure 3" from the top screw to the bottom screw, and 3-1/2" across.
Additionally, they did also mention that the O-ring is 3-1/2" in diameter.
For a replacement o-ring, you can use the:
-Oil Cap O-Ring # 92127.
I have included a diagram and a review video for you to check out if you have not alerady. view full answer...
The Dual Function Air Spring Control Panel # F2260 that you referenced would be just what you'd need to give you the ability to have two different psi levels in two different areas like you mentioned. The black arrow would show you how much pressure is in one set and the red in the other. view full answer...
If you really liked the Dexter brakes and want to continue to use that brand I can help you find exactly what you are looking for. Otherwise, no, you do not have to replace the electric brakes on your trailer with the same Dexter brand.
The Nev-R-Adjust Electric Brake Assemblies, part # K23-478-00 LH (driver side) and part # K23-479-00 RH (passenger side), from Dexter that you referenced are great options since you do not have to keep adjusting the brakes. These assemblies are 10 inches... view full answer...
Since you're using two air conditioners, the 13,500 Btu air conditioner will give you more than enough cooling, so you can go with a unit from Advent:
- Advent Air RV Air Conditioner w/ Air Distribution Box and Wall Thermostat - 13,500 Btu # ADV94FR view full answer...
We do have Firestone Ride-Rite air bags available for a 1986 Chevrolet P-30. They are the Firestone Ride-Rite Air Helper Springs # F2080 for the rear. We do not have Firestone Ride-Rite's for the front of the P-30.
For front and rear we have the Air Lift 1000 Air Helper Springs # AL81560 for the front and the Air Lift LoadLifter 5000 Ultimate Air Helper Springs # AL88203 for the rear.
The Firestone Air Command II - Analog Gauge w/ Heavy Duty Compressor # F2219 would allow you to inflate/deflate... view full answer...
Go Power Retreat Solar Charging Kit w/ Digital Controller - 100 Watts - 5.43 Amp # 34272635 is expandable to multiple panels using the Go Power Retreat-E Expansion Kit - 100 Watts - 5.43 Amp # 34272634.
If you want more power, you may want to consider the The Go Power Overlander-E Expansion Kit # 34282182 which can add the Go Power Overlander Solar Charging Kit w/ Digital Controller # 34282181 to give you a larger system.
Either option can be expanded with more panels as desired. I've... view full answer...
For a motorhome on a P30 chassis with a 36" frame width you would need to install an adjustable-fit hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. The cross tube for this hitch is 44" in length but can be trimmed down to fit your chassis. The mounting brackets have a 7" drop to help clear your rear fascia, but we also offer this with a 16" drop # 41990-16 if needed. view full answer...
Unfortunately there currently isn't a steering stabilizer fit available for your 1996 Chevy P30 Chassis. I can completely understand where you're coming from with the poor ride quality in motorhomes having driving numerous models here so I do have some other recommendations for you.
You can replace your front coil springs with the SuperCoils Custom Suspension Coils # SSC-11 to help stiffen up the suspension. From there you can install the Timbren Front Suspension Enhancement System #... view full answer...
The front Firestone Coil-Rite Air Helper Springs # F4100 is the correct kit for a 1994 Chevy Class A chassis (should be the P-30) you have for your Winnebago motorhome!
If you're looking for rear air bags as well then you need one of the following depending on the GVWR of your RV:
- GVWR Less Than 14,500 lbs # AL88203
- GVWR Greater Than 14,500 lbs # AL88219 view full answer...
The Roadmaster Reflex Steering Stabilizer, # RM-RBK3-RSSP30, is the correct stabilizer for your 1991 Chevrolet P30 Motorhome. Everything you will need is included, stabilizer, custom mounting brackets, and hardware. No drilling or welding is required so installation should take about 1 hour. view full answer...
If your P30 wheels are 19.5 inch diameter wheels with 10 lugs and 10 hand holes the Namsco Hub Cap Wheel Cover # NA7195B1 will fit the wheels. view full answer...
Go To Results