Does your Camaro have two exhaust pipes or a single exhaust pipe? We only have one hitch that fits your vehicle with the Curt # C11117 but this cannot fit versions of your 1995 Chevy Camaro that have dual exhaust.
This hitch would work great to carry a bike rack like the Hollywood Racks # HR200Z. view full answer...
The Curt # C11117 Class I hitch fits 1995 single exhaust Chevy Camaro models. It won't fit models with twin tailpipes next to each other or models with two cutouts in the bumper for the exhaust to pass through. view full answer...
The heaviest-duty fan that might work for you is one that moves 6,000 CFM of air:
- Flex-a-lite Dual 15" S-Blade Electric Radiator Fans with Shroud Assembly - 6,000 CFM # FLX293
This is a universal fit so you just need to make sure you have the room, as it measures overall 31-7/8" wide x 17" tall x 4-1/2" deep. view full answer...
Yes, you can use Curt trailer wiring harness # C56197 on your 2015 Chevy Camaro with incandescent lights and trailer with LED lights. I have included a link to the installation instructions for you. view full answer...
The Curt Trailer Hitch # C11117 will require drilling to install on a 1991 Chevy Camaro. There are two holes that need to be drilled with a 9/16" drill bit in order to secure the hitch.
Please keep in mind that this hitch does NOT fit models with twin tailpipes or single exhaust models that have the bumper with two cutouts for the exhaust.
I have added a link to the installation instructions for you to check out as well. view full answer...
I have some recommendations for you, but currently there is no trunk mounted bike rack that will work for both a 2010 Chevrolet Camaro and a 2017 Lincoln MKZ.
For the 2017 Lincoln MKZ, I recommend the Yakima HangOut 2 Bike Rack, part # Y02637. This is a cost effective rack that provides protection for both your bike and your car's finish by securely supporting your bikes. It also fits most factory spoilers.
For the 2010 Chevrolet Camaro, the only bike rack that will work for you is the... view full answer...
Engine oil and transmission fluid coolers such as the Derale Atomic-Cool Remote Fan-Powered Oil Cooler # D15450 are not vehicle-specific. They can be installed on just about any vehicle that has a suitable mounting point.
Since this is a remote cooler that does NOT depend on passive air flow from the vehicle's motion it will cool your oil at any speed and you can put it pretty much anywhere you want to.
The kit is intended to fit all vehicles with engine block oil filter landings ranging... view full answer...
Yes. The Curt # C59496 will provide enough power for incandescent lights on a trailer without issues and is a confirmed fit on your 2015 Chevy Camaro. view full answer...
The Curt Trailer Hitch # 11117 that you referenced should work well on your 2001 Chevy Camaro. Having dual exhaust will not cause a problem is this hitch is confirmed to fit other F-bodies like yours that come standard with dual exhaust.
You will need to be sure you do not exceed the towing capacities of your vehicle and this hitch with your trailer. Your owners manual will have the towing capacities listed for your vehicle.
When determining the overall towing capacity of a setup you... view full answer...
Since you have a 2015 Camaro LS there are extremely limited options for bike racks. The only choice if you do not want to add a hitch is to use the SeaSucker Komodo Bike Rack for 1 Bike item # 298-BK1910-BK. This will mount one bike weighing up to 45 lbs to the rear of your Camaro using suction cups.
To use a two bike bike rack with your car you will need to add the Draw-Tite Trailer Hitch item # 24850. This hitch is custom fit and bolts to your Camaro with included hardware. It does... view full answer...
To determine if the MagnaFlow Exhaust Cutout # MF10784 will fit your 2017 Chevy Camaro you will need to go by the inlet/outlet diameter of the part. On this cutout the inlet and outlet are both 2-1/2 inches. It is possible for a muffler shop to adapt it to fit if your exhaust is not the right size.
We do have a 2-1/4 inch version, # MF10783, and a 3 inch version, # MF10785, as well. view full answer...
Curt requires the use of # 18050 stabilizing straps on the hitch # C11900 for non-supported loads like bike racks or cargo carriers like the Curt # C18145 cargo carrier.
I really like how well hidden this hitch is. If it were me, I would add the etrailer # 22281 rubber hitch cover.
I looked into the installation instructions, and among the typical tools required, there were a few special tools that you should consider getting to make the install go easier and faster. You may want the... view full answer...
The Draw-Tite Sportframe Trailer Hitch Receiver # 24850 measures about 9" from the hitch pin hole to the rear of the bumper. The Swagman XTC2 Bike Rack for 2 Bikes # S64670 measures about 8" from the hitch pin hole to the nearest wheel hoop as you can see in the photo I attached. The means that the bike rack will likely interfere with the rear bumper and the only way around that is to use a hitch adapter such as CR Brophy Hitch Extender for 1-1/4" Hitch Receivers - 5-3/4" Long # hes6. This... view full answer...
There is indeed a trailer hitch receiver that fits your 2011 Chevy Camaro convertible, so long as you don't have the Ground Effects package; it is the following part number:
- Convertible: Curt Trailer Hitch Receiver # C11222 view full answer...
I do show the Curt Trailer Hitch Receiver part # C11222 as a fit for a 2012 Chevy Camaro 2SS. I checked with the manufacturer and they do show fit on SS models although they don't break it down into 1SS and 2SS. There are no structural differences between the two so there should be no fit issues. view full answer...
The Cruiser Fastener Caps # CR82650 that you referenced are a universal fit and don't have a specific size bolt that they fit.
I have attached a link to our available selection of fasteners and caps for you to reference. view full answer...
The frame on the convertible models has some differences with regular hardtop models and some hitches will not fit. We do have a trailer hitch that you can use on your convertible 2012 Chevy Camaro as long as it does not have the ground effects package. You can use Curt trailer hitch # C11222.
If you plan on doing some towing first consult the vehicle owners manual to make sure it is permissible to do so. The correct ball mount for this hitch and vehicle is # C45520. You will also need... view full answer...
The ball mount help article also mentions that on a Class I or II hitch you have to use the ball mount indicated by the hitch manufacturer and specified in the instructions. In the instructions for Curt trailer hitch # C11373 specified ball mount is # C45521 which is a Class II ball mount.
The reason that this Class II ball mount will fit this Class I hitch is that Curt does not install a safety stop in their Class I hitches to prevent installation of Class II accessories. All other hitch... view full answer...
You are correct. We do have the Curt wiring harness # C56197 listed as a NO-FIT for a 2014 Chevy Camaro that has LED tail lights because those models require a powered converter to power the trailer lights without damaging the vehicle wiring. On models that do have LED tail lights you would need to use Curt harness # C59236. view full answer...
Go To Results