The Curt Trailer Hitch Receiver # 13375 for your 2022 Mercedes-Benz Sprinter 3500 is 32-1/8" wide between the mounting brackets(see image). view full answer...
I went into our warehouse with a digital caliper to take the requested measurements for you. The Replacement Gear Kit for etrailer and Ram Sidewind Jacks - 2,000 lbs and 5,000 lbs # TJA-2000S-GR has an inner diameter of 0.5 inches and outer diameter of 1.36 on the gears. The pins have a 0.18 inch diameter and are 0.86 and 0.98 inches in length. I've attached a photo to assist. view full answer...
It should, I looked up the specs on your Hobie Outback Mirage and it weighs 75 lbs, whereas the Yakima JayLow Kayak Carrier # Y04073 that you referenced has a weight of 80 lbs so it should work well for you.
You will also want to determine the roof capacity of the vehicle you plan on carrying this with and be sure not to exceed this figure either. The lowest rated component in your setup is the overall capacity since your setup is only as strong as it's weakest link. I attached a review... view full answer...
The black power wire that comes with trailer wiring harness # 119250KIT is 12 gauge. I have included a link to a video showing an example installation on a GL-series of this wiring harness for you. view full answer...
The weight capacity of a trailer is more than just the axle and tire capacity. The frame of the trailer, suspension, brakes etc. are all parts of the equation that you need to consider. Your trailer should have an axle weight capacity as well as the weight capacity of the trailer. It is possible that going to a higher rated axle will give you additional weight capacity for the trailer, but the axle would have to have been the weakest link.
Easiest way to inspect your current axle would... view full answer...
When we installed the Draw Tit Hitch part# 75087 on a 2003 Mercedes M Class we found that the hitch pin hole stuck out the exact same distance as the furthest point out on the rear bumper. So that means the hitch opening itself would stick out 2-1/2 inches past the rear bumper. view full answer...
From the bottom of the Curt hitch part # C13276 down to the ground on your 2019 Mercedes Benz Metris will measure right at 10 inches. I attached a picture that shows that it fits up to the bottom of the rear bumper about as tightly as it could. I also attached an install video link with more info as well. There isn't an option with more clearance available. view full answer...
The Curt Trailer Hitch Receiver # C13290 that fits your 2020 Mercedes-Benz GLC300 has a shipping weight of 40 lbs so minus packaging you're looking in the ballpark of 37 lbs for the hitch.
Attached is an installation video of this hitch being installed on a 2020 MB GLC-Class that you can check out. If you let me know what you plan on using the trailer hitch for, I can make some recommendations for you! view full answer...
There are two options for Rhino-Rack Pioneer Platform Racks for your 2019 Mercedes-Benz Sprinter with high top and factory roof rails. The first is the 100" Long x 62" Wide item # RR85ZW. The second is the 60" Long x 62" Wide item # RR25ZW. Both are confirmed to fit your Sprinter. view full answer...
The FloTool Super Duty Drain Container - 58 Quarts # FT42008 measures 37.5" long x 26.8" wide x 10.2" tall and will hold up to 58 quarts of fluid. view full answer...
I spoke with my contact at Bestop who gave me the following dimensions for the Bestop TrailMax II Fold & Tumble # B3943915:
Base:
Length - 40-1/2"
Depth - 20"
Cushion Thickness - 5-1/4"
Backrest:
Indented Length - 30" (longer part measures 40-1/2")
Height w/o Headrest - 10"
Height w/Headrest Up - 26"
Height w/Headrest Down - 23"
I have attached a photo giving the basic dimensions for you to check out. Please note that this is designed to fit 1997-2006 models of the Jeep TJ and Jeep Wrangler... view full answer...
The Draw Tite # 75601 and the Curt # 13358 that you referenced both are a fit for your 2017 Mercedes Benz Sprinter 2500. They have very similar ground clearance but the Curt has the slight edge as it seems to sit a bit higher. I attached a picture that shows the difference. The Curt is in the top picture. view full answer...
Carr Custom-Fit Side Steps # CARR105771 are confirmed to fit your 2017 Mercedes-Benz Sprinter 3500 and they have a height drop of 5-inches from the mounting point on the rocker panels. The linked video will show you an example installation. The mounting hardware is included with these USA-made steps. view full answer...
The highest rated trailer hitch we have for a 2018 Mercedes-Benz Sprinter 2500 4x4 with 170" Wheelbase is the Curt Trailer Hitch Receiver part # 13358 if you have the factory step bumper which is rated for 5,000 lbs gross trailer weight and 500 lbs tongue weight or the Curt Trailer Hitch Receiver part # C13388 if you have the standard bumper which is rated for 6,000 lbs gross trailer weight and 600 lbs tongue weight. Unfortunately, there isn't any way to strengthen the tongue but the factory... view full answer...
According to Thule, the frame of the Thule Elite Van XT 2 Bike Rack for Sprinter Rear Door # TH302043 measures 9-7/8 inches from the mounting points to the frame. view full answer...
The magnet itself is 3 3/8" wide and the piece that it is on is 4" wide, so you'll need at least 4" of room to mount the Thule Telescoping Ladder for Van # TH301404 on your 2013 Sprinter. view full answer...
We've pulled one of the # MT70066 ball mounts from stock and got the measurement for you. The lateral distance between the hitch pin hole in the shank and the rear of the top receiver is 5 inches. I've shown this dimension, and others in the photo I've provided for you.
If you click the provided link, you can see a product description video featuring the # MT70066 ball mount. view full answer...
The distance from center hole to center hole across the hitch on the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11815 is 40-1/8". This hitch fits the 1994-2000 Mercedes-Benz C-Class Sedan as well as the 1998-2003 Mercedes-Benz CLK-Class. view full answer...
I attached a picture of the Curt hitch # C13411 installed on a similar Mercedes that you can show your customer to see what it looks like installed. view full answer...
In order to select the correct hatch cover for your 2009 Forest River camper you need to know your hatch cut out size, or you can use a universal option, and I'll go over the selection of options we have and you can use this to determine which access door you can use once you take the appropriate measurements.
The Valterra Electrical Cable Hatch for RVs - 8-1/2" Long x 8" Tall - White # A10-2151VP or Black # A10-2151BKVP will fit your camper if it has a 6-13/16" long x 6-3/8" tall hatch... view full answer...