The motorcycle license plate frame part # CR77000 that you referenced is designed to fit the standard motorcycle license plate frame size of 4 inch by 7 inch. view full answer...
The Cruiser Accessories License Plate Mounting Plate # CR79150 has the exact same dimensions as a license plate so it would not be visible behind one. It would just appear as if the license plate was 1/4 of an inch off the back of the surface it is mounted to. view full answer...
Yep, the Chevy License Plate Frame # CR10437 sure does fit a 2014 Chevy Silverado 1500 LTZ.
This is a chrome-colored frame with a gold Bowtie Chevy emblem which will integrate seamlessly with your '14 Silverado. view full answer...
Yes, the Trailer License Plate Mount Bracket # LP15SB that you referenced will allow a license plate with mounting holes that are 6 inches apart to be installed on it. view full answer...
The Elite Stainless License Plate Frame, part # CR21010, you mentioned is made of stainless steel, and measures just .129 inches thick.
I have attached a photo of this frame and have the dimensions noted on the photo you can check out. view full answer...
The top of the shank L-brackets of the Front Mount Trailer Hitch License Plate Relocation Bracket, item # 5443, is about 3-1/4 inches to the top the license plate bracket. The hitch pin is not included with this item. You could use the Trailer Hitch Receiver Lock - Flush Design for 2 inch Trailer Hitches, part # e98880, or the Pin and Clip For Class III, IV and V Trailer Hitch Receiver, part # PC3. view full answer...
The mounting holes on the Twins Motorcycle License Plate Frame part # CR77930 are spaced 6" apart side to side and 3" apart top to bottom.
Please note, I was not able to find the mounting hole spacing for Minnesota Motorcycle License Plates online so you will need to measure this for yourself. view full answer...
I went out into our warehouse and measured a Stainless License Plate Frame # CR21110 that we had in stock and found that it measured 12-3/8 inches by 6-1/2 inches. view full answer...
The Steel Fasteners for License Plates and License Plate Frames - Standard - Qty 4 # CR80230 are 1/4 inch diameter by 3/4 inch long. This is the standard diameter for license plate hardware, so if you have a smaller hole, you may want to consider enlarging it for compatibility or using stainless or zinc plated screws from a hardware store that will fit the current holes. view full answer...
Mounting hole spacing for the Ultimate Tuf Combo License Plate Frame # CR62510 is 7 x 4-5/8-inches on hole centers as shown in the linked photo. This plate cover includes mounting nuts/bolts and decorative bolt head covers that match the frame. Both standard and metric hardware is included. view full answer...
The Stainless Steel License plate frame part # CR21010 that you referenced is 5-3/8 inches tall internally and 11-13/32 inches wide internally. view full answer...
I checked with the manufacturer and was able to get the exact dimensions for you of the Tuf Combo License Plate Frame and Smoke-Tinted Shield - Black # CR62052.
They say this frame measures 12.3 inches long x 6.2 inches wide (in fractions that'd be just under 12-5/16" and just over 6-3/16").
To mount the # CR62052 you will need one of two kits; for import vehicles the Star Pin Locking Fasteners # CR81300, and for domestic vehicles the Star Pin Locking Fasteners # CR81200. view full answer...
To get the dimensions you asked for, I went out to the warehouse and got this item and measured with a dial caliper. The bolt in the Rattle Stop Locking Fasteners for License Plate Frames, # CR81400, is .533 inches overall length and the thread length is .380 inches.
The threaded insert is .412 inches overall height. the threaded portion that sticks up is .259 inches tall and the washer end that has a rubberized cover on it is .145 inches thick.
When threaded together with a minimal number... view full answer...
I spoke with my contact at DWD about the Ebony Finish, Stainless Steel Saturn License Plate, # 312923, for your 2008 Saturn Aura XR. She stated that the plate measures 12 inches long and 6 inches high, and is about 3/8 inches thick. view full answer...
Yes it certainly is. The "Cadillac" symbol is raised lettering on the Ebony Finished Stainless Steel License Plate Cadillac Chrome # 310233.
I have added a link to each of our license plates with the Cadillac symbol for you to check out. view full answer...
The vertical distance you are looking for from the mounting holes of the # PM436B to the mounting holes for the license plate is 1-3/8 inches. view full answer...
The Optronics License Plate Light Bracket # BK31BB is a flat bracket. This bracket is designed to work with either the Optronices Mini Trailer License Plate Light # LP31CB or the LED version # LPL31CB view full answer...
I am including pictures of the Optronics Trailer License Plate Mount Bracket, part # LP5SB, and the Optronics Trailer License Plate Mount Bracket, part # LP10SB with the dimensions and hole diameters listed. view full answer...
The difference between the Peterson Round Trailer Tail Light Right Hand # 431800 and the Peterson Round Trailer Tail Light Left Hand # 432000 is that the left side # 432000 comes with a license plate bracket and has a light to illuminate the plate.
You could mount part # 432000 and 431800 on either side of the trailer, but then the license plate of your trailer may not be illuminated. You will want to check your local laws to make sure that you can mount the license plate of your trailer... view full answer...