I sure can; I have added a photo for you with the dimensions of the mounting hole for the 50 amp SmartPlug inlet and connector. This comes in your choice of three different colors, and the dimensions are the same for each:
- Black: SmartPlug RV Power Inlet and Connector - 50 Amp # SM76FR
- Gray: SmartPlug RV Power Inlet and Connector - 50 Amp # SM66FR
- White: SmartPlug RV Power Inlet and Connector - 50 Amp # SM46FR
Overall the whole unit is 4-1/2 inches tall and 3-1/4 inches wide. view full answer...
I can definitely understand not wanting to re-size your current 2-1/2 inch hole, but the smallest size hole that will allow a 30 amp rv power inlet is 2-1/2 inches in diameter, so that would be the smallest hole size you would need. For that you would need the following Furrion inlet:
- Furrion Replacement RV Power Inlet - 30 Amp Twist Lock - Stainless Steel # F30ITSSS
I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
The female end, or the power inlet, with the weather resistant cover is 3.25 inches at its widest point. 4.5 inches tall and 3.75 inches long.
The male side of the plug is 4 inches long 3 inches wide and 3 inches tall.
Here are the two different color schemes with the same dimensions.
SmartPlug RV Power Inlet and Connector - 30 Amp - Gray # SM87FR.
SmartPlug RV Power Inlet and Connector - 30 Amp - White # SM77FR. view full answer...
The distance between each of the mounting holes on the Mighty Cord Replacement RV Power Inlet is 2-7/16", as you can see in the accompanying photo.
This inlet comes in your choice of either Black # A10-50INBKVP or White # A10-50INVP. view full answer...
The diameter of the round part that goes in the RV is 2-5/8 inches on the 50 amp Hughes Autoformers Safe View Smart Power Inlet # HU27VR. view full answer...
I went to our warehouse and measured the Mighty Cord Replacement 30-Amp RV Power Inlet # A10-30INBKVP and found its four mounting holes are 1/8-inch diameter and they are spaced apart 2-7/16-inches on center. view full answer...
Please note the attached image(S) showing requested measurements of the Stainless Steel Inlet for SmartPlug RV Power Cord, # SM39FR. The overall depth from back of inlet to closed face of of the stainless steel cover is 3.33". The stainless steel cover, from back of piece that mounts against trailer to the same closed face is 0.83". With the orange portion that sets inside mounting location being 2.18". The overall height of the stainless steel face plate is 4.15" and the width being... view full answer...
Yes, the dimensions of the 30 Amp SmartPlug RV Power Inlet and Connector, found in Gray # SM87FR or White # SM77FR is as follows:
Receptacle - 3.25" wide x 4.5" tall x 3.75" long (or deep)
Plug - 3" wide x 3" tall x 4" long (or deep)
Attached is a review video as well as some dimensional photos for you to check out! view full answer...
The Mighty Cord RV Extension Cord - 50 Amps - 10' Long # A10-5010EH weighs approximately 8lbs and the Mighty Cord RV Extension Cord - 50 Amps - 15' Long # A10-5015EH weighs approximately 11lbs. view full answer...
I've drawn up a little diagram below of the Hughes Autoformers Safe View Smart Power Inlet # HU87VR dimensions. Based on what I found a 3-1/2" round hole would be a bit too large and would require you to first place some sort of cover over the hole and cut a hole in the cover to mount the inlet into. view full answer...
The Camco RV Drain Trap, part # CAM37262 is designed for 3/4 inch diameter drain hoses.
The threaded inlet portion of the trap measures 1-3/4 inches at the threads. view full answer...
The inlets on the Phoenix Faucets Catalina RV Kitchen Faucet w/ Pull Down Spout # PF221404 measure 8" apart on center.
I've attached a photo demonstrating this as well as linked a review video for you to reference! view full answer...
The Valterra Water Inlet for RVs part # A01-0176LFVP is a universal water inlet that works on most trailers. It has a outer flange that measures 4-1/2" diameter which I have attached a photo of for you. It should work well as a replacement for the one you have now. view full answer...
The base of the Ultra Faucets RV Bar Faucet part # 277-000069 measures 2" deep and the inlets are centered on the base so if you simply divide by two you can get the clearance from the center of the inlet to the back of the base which is 1". view full answer...
The two inlet shanks of the Patrick Distribution RV Kitchen Faucet # 277-000014 that you referenced are separated by 8 inches on center. view full answer...