We do not personally design and build the MORryde Rv Cargo Sliding Trays but we do carry two sizes close to your needed 45" x 90" dimensions.
The MORryde Sliding Tray for RV Cargo Compartment - 90" x 42" # MR35FR and the MORryde Sliding Tray for RV Cargo Compartment - 90" x 48" # MR32FR. view full answer...
I think what you are looking for is the MORryde RV Cargo Sliding Tray - 90" x 29", # MR69FR and the Height Adjustment Kit for MORryde RV Cargo Sliding Trays, # MR34VR.
Please note the linked product review video below. view full answer...
Yes. The MORryde Sliding Tray for RV Cargo Compartment - 90" x 33" - 800 lbs - 2 Way # MR46FR is 33" wide and is the same cargo slide as the # MR69FR, just a bit wider. view full answer...
The 72" MORryde RV Cargo Sliding Tray # MR74FR is their longest tray with an 80% extension. They do offer a 90" Tray # MR84FR which is also 20" wide and has a 60% extension. Their 90" trays are able to slide on either side as they are designed to fit the storage compartment of travel trailers and 5th wheels which open on both sides of the camper. The trays go from 72" to 90 on the 60% extensions. view full answer...
We do have the trim kits available for the Kwikee SuperSlide II Tray Assembly Kit for RV Cargo Compartment - 60 Deep # LC370787 that you referenced. You just need to choose from the following to match the width of your compartment:
24" - # LC370676
32" - # LC370682
48" - # LC370757
You'll also need to acquire some plywood at your local hardware or lumber store to complete this setup. view full answer...
You will need risers but we have them. The MORryde RV Cargo Sliding Tray, # MR47FR will have 1.57" of clearance from the bottom of the tray to the bottom of the slides. But we have the Height Adjustment Kit, # MR34VR for trays being installed in compartments with a lip taller than 1-5/8". Use this to raise your tray to sit at either 2-1/2", 2-3/4", or 3-1/8" higher. Please note the linked product review video below. view full answer...
We do not offer the MorRyde brand but we do have sliding cargo storage trays for RVs, including part # LC370782 that you referenced. These are available in a range of sizes and you can see all of them by clicking on the linked page. view full answer...
The Kwikee SuperSlide systems, like part # LC370774, do not have a lift kit available so you would need to build one yourself out of wood in order to clear the 3" lip for your compartment door.
You might be able to use the Height Adjustment Kit for MORryde RV Cargo Sliding Trays # MR34VR, but would most likely need to drill holes into the tray track in order to mount it on the kit since it was intended for use with MORryde trays. view full answer...
For a slide-out tray that will fit your generator that has base dimensions of 24" x 34" you can use the MORryde RV Cargo Sliding Tray # MR37FR which has measurements of 36" x 26" and can hold up to 800 lbs. view full answer...
The largest 90" 2-way sliding tray for your 46.5" door width is the MORryde Sliding Tray for RV Cargo Compartment - 90" x 42" - 800lbs - 2 Way # MR35FR. view full answer...
We have the MORryde RV Cargo Sliding Tray # MR93FR which is 90" x 39" with a 60% extension and is the closest available to the specifications you listed.
From what I could find in my research from MORryde is that the 80% extension trays only get up to 72" long. The 39" is also the closest to 40" they have when paired with the 90" length. view full answer...
The only sliding tray we carry with the 36" x 48" dimensions you need is the MORryde Sliding Tray for RV Cargo Compartment # MR65FR. It has an 800lbs weight capacity and does come with a carpeted flooring. It only comes in a light gray but it is able to be bolted to the concrete floor of your facility. view full answer...
There are cargo carriers that can be fitted with add-on bike carrier accessories. Good for you for trying to plan ahead!
However any item, such as a bike rack or cargo carrier, that will be installed in a hitch that is on the rear of a trailer or motorhome must be specifically rated for that RV application. Regular bike and cargo carriers made for cars cannot be used on RVs. They are not strong enough.
The reason is that the typically longer distance between the rear axle of an RV and... view full answer...
There is a MORryde cargo slide that meets these dimensions but only offers a 1-way slide, part # MR53FR. There is another model # MR33FR with the same dimensions and offers a 2-way slide, but it has a 80% extension and lower weight capacity at 500lbs. view full answer...
The only folding RV bumper mount cargo carriers that we have are all steel, not aluminum. We do have these available in a few different sizes, which I have listed below.
- 24x40 etrailer Cargo Carrier for RV Bumper # e99050
- 24x60 etrailer Cargo Carrier for RV Bumper # e99049
- 24x64 etrailer Cargo Carrier for RV Bumper # e83YR
- 24x84 etrailer Cargo Carrier for RV Bumper # e96ZR view full answer...
We have exactly the size that you need. The MORryde Sliding Tray # MR46FR is a two way slide that is 90" long x 33" wide. This sliding tray has a 800 lb weight capacity. view full answer...
The only slide slickers we carry are the Lippert Carpet Protectors for RVs with Slide Outs # LC134993 which measure 40" long x 5" wide. This will be a standard size and should be able to fit a wide variety of slide out sizes. view full answer...
It looks like you were looking at the bumper mount cargo carrier options for your RV. The 24"x84" etrailer Cargo Carrier for RV Bumper # e96ZR is the closest option to the 56" x 90" that you are wanting.
You are not going to find a cargo carrier that extends out from your bumper 56". This is because it would extend too far out and cause extra stress, because the further the weight is extended the more stress it puts on the bumper.
Technically you could get multiple of the Mount-n-Lock... view full answer...