Jeff, we do have just tires available but it looks like the closest tire we have to your size is the Kenda Karrier S-Trail ST145/R12 Radial Trailer Tire # AM10130.
These are 145/80 R13 tires so they'll still work with your current wheels, but is going to be 0.7" shorter, and 0.4" narrower, just so you know. view full answer...
Hey James,
If the inner tube of the jack is bent then there's unfortunately not going to e a way to fix the jack and you'll have to use an angle grinder to cut off the old jack and replace it. If the wheel is detachable and the inner tube is still ok then we'd be able to just swap out the wheel.
If replacement is the only option then I recommend the Round Swivel Marine Jack w/ Wheel # MJ-1206B. This jack comes with brackets to clamp onto the frame so that you can easily move it around... view full answer...
Hey there Brad,
We do have a replacement for the 125255UC grease seal; the correct seal is the following:
- Double Lip Grease Seal # 34823 view full answer...
Thanks for reaching out, Michael!
The widest roller we have is the 18" Long Yates Keel Roller for Boat Trailers # YR18244-165EC which installs on a trailer using the CE Smith Universal-Fit Split Panel Brackets # CE10500G, the 19" Roller Shaft w/Cap Nuts # 107-30A, and either bolting into the trailer frame or around it with U-Bolts. Since I'm not sure what the size of your frame is I've gone ahead and added a link to our U-Bolt kit selection for you to filter through, but I'd be more than... view full answer...
Currently the only way we have tail lights with the quick connector like you have is the Drivers # STL37RPG and Passenger # STL36RPG tail lights. These lights are submersible so they are compatible with your ShoreLand'r boat trailer. view full answer...
Thank you for all the information as well as the image Mark. Based on your information the Dexter Hydraulic Trailer Brake Kit # 23-398-399 will work as a replacement. These assemblies have the same 4" diagonal and 2-3/4" stud spacing. The pads are also the 1-3/4" wide for a 7" diameter drum view full answer...
You would simply use the 7-Way Round RV Style Trailer Connector # A7WCB to change your boat trailer from the 4-Way Flat # 18172. The 7-Way Molded Trailer Wire Connector # H20043 you found would also work but it contains wires you do not need as you will still only connect your 7 wires to the 4 pins for the ground, running lights, and left/right turn signals/brake lights. view full answer...
Hey Erik, so if the coupler on your 2007 MasterCraft boat trailer is labeled a UFP or a Dexter actuator and looks like the # DX99FR then yes this inner member is correct replacement to get it working again. There isn't a way to look up what your trailer has on it so you would have to identify it first. view full answer...
Hey Henry, it looks to me like a standard 5 pole harness so you can use the 25 Ft 5-Way Trailer Wiring Harness - Wishbone Style # A25W5B as a replacement. view full answer...
The Tandem Axle Teardrop Trailer Fenders for Boat Trailers # HP54VR are only available as a pair. I understand you just need one right now but this is the only option available. The good news is you would have a spare if the fender you install gets damaged in the future. view full answer...
Tom, the Kodiak Disc Brakes # KOD69FR you're looking at will work great as a replacement. You're probably already aware that TDE is no longer a company that's in business, so a full replacement is going to be your only choice.
This brake kit has a 1 piece hub-and-rotor assembly which helps reduce the chance of uneven rotor wear and uses a vented design to dissipate heat faster and prevent premature brake pad wear. view full answer...
This will depend on if you have disc or drum brakes on your triple axle boat trailer.
Disc Brake Kit # HS381-9067
Drum Brake Kit # HS381-9066
Each kit contains the correct electric over hydraulic actuator, 7-way wiring and breakaway components. If you can send me some images of your current coupler along with the weight of your trailer and boat I can make a recommendation for a replacement coupler. And depending on where you intend on mounting the actuator you may need a hose like the... view full answer...
As your 2008 Ranger Boat Trailer has a swing away tongue with the Tie Down Model 70LP brake actuator the Dexter Disc # DX73FR or Drum # DX67FR actuator is likely going to be your best option. Both of these are a weld on application so you would need to have your current actuator removed and the new one welded on in place on the swing away portion of the trailer tongue. view full answer...
Hey Brandon,
Based on the information you've provided I recommend the DeeMaxx Disc Brake Kit # DE66YR. This disc brake kit has a corrosion-resistant "Maxx" coating finish on the hub/rotors, calipers, and brackets for a salt spray rating over 1,000 hours. It uses the same bearing sizes and and has the same wheel bolt pattern at 5 on 4-1/2. The brake lines should connect to the inlet on the caliper but they do sit a little lower than the original calipers. I've attached a video below where... view full answer...
First David, just to be sure if you are going to need to cut down the Yates Keel Roller for Boat Trailers # YR10000 you will want to measure the width of your mounting brackets. This particular roller is 9-3/4" wide and designed to fit a 10" wide roller. As your trailer is older the rubber can shrink slightly over time and you may not need to cut the roller. If you do need to cut the roller down slightly do be sure to remove the end caps on this particular roller first as they will need... view full answer...
Hey Brian,
To replace the brake pads on a 3,500lb assembly you would need four of the Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate - 3,500lbs # K225CPSS. I've attached a short video below where Dave will walk you through the replacement if you're wanting swap them out yourself. view full answer...
Based on the information I could find it appears your Shoreland'r LUV40TMXWMS1-16 uses standard 3,500lb axle and hubs. I always recommend verifying this as I have seen manufacturers make changes or trailers get axles changed due to being damaged in transit. These hubs will fit the 1.98" Bearing Buddy # BB1980A-SS. The CE Smith Trailer Idler Hub Assembly # CE13515 you found does contain the correct size bearings and grease seal for a standard 3,500lb axle and will also fit the Bearing Buddy... view full answer...
If you need a replacement tongue that isn't something that we offer. You can see if the manufacturer offers a replacement since it looks like it folds. If they don't have a replacement you would have to take it to a shop that could add a new tongue along with a coupler hinge kit like # FHDPB330301 to keep the folding functionality.
I can't do much with the VIN but it does look like that has a Dexter A-60 in the end of it based on the pictures I found. If you're able to remove the actuator... view full answer...
Hey Doug,
You can definitely swap out the 5' bunks on the CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks # CE48870 with the 7' long replacement bunks # CE27845 for more support. I would just flip the front mounting brackets to have them spaced a bit further apart to support the extra 2' of bunk length hanging off. view full answer...
A slotted bunk bracket like the part # DL21742 would work really great in place of what you have now. You could line up the bolt holes on our crossmember with the slots of these brackets and you'd be good. view full answer...
Go To Results