Hey Larry, thanks for reaching out!
The correct part to replace your 1510000006 motor is the Replacement PowerGear RV Above Floor Slide-Out Moto # LC368417.
The Replacement Motor # LC386322 you were looking at does look similar, but it isn't the correct part you need. view full answer...
Hey Kelly, yes the etrailer generator part # 333-0005 would be able to supply enough power for your two slide outs on your travel trailer that has a 30 amp plug. view full answer...
Hey Ellen, thanks for reaching out!
The Global Link Replacement J38 Roller for RV Slide Out # 295-000027 measures 4-5/8" long x 1-3/4" wide x 1-1/16" tall so you'll want to compare that to the roller you're needing to replace. I wasn't able to find any information on the part 640078 you asked about. view full answer...
Based on the parts diagram from Winnebago your 2013 Itasca Suncruiser 32H will use the Lippert Replacement 500:1 Motor for Electric In-Wall RV Slide-Out System # LC287298. view full answer...
Currently a 10' Awning # LCV000211446 is going to be the narrowest we carry. You would need the Arm Set # LC759516 and just under 10' of Rail Extrusion # LC715217 to install it. Do note the width of an awning is not measured on the fabric but the width of the center of the arms from one side to the other.
A 9' wide awning would have to be special ordered from a local RV dealer. view full answer...
The MORryde RV Cargo Sliding Tray # MR47FR has 1.57" of clearance from the bottom of the tray to the bottom of the slides. More than likely you will need the Height Adjustment Kit # MR34VR which will raise the tray to sit 2-1/2", 2-3/4", or 3-1/8" higher. view full answer...
Hi Norm,
The components at the front end of the MORryde RV Cargo Sliding Tray # MR89FR are all very close to being inline with each other. The lip on the tray sticks out the furthest and even then it's a negligible amount. MORryde doesn't list a clearance requirement but I'd give yourself at minimum 1/4" - 1/2" from the opening to avoid any issues. Most RV compartment doors sit flush with the wall because of the flange that prevents the door from swinging in so as long as you're behind... view full answer...
Hey Kim, to loosen the tension on your Solera RV Slide-Out Awning # LCV000163285 you will need to remove the pin and then spin it counterclockwise for the left-hand side and clockwise for the right-hand side.
You can see this demonstrated in the attached video around the 7:15 minute mark. view full answer...
We have two options to attach awning fabric to the side of your RV. They are the 8' Solera Awning Rail Extrusion in white item # LC715216 and in black item # LC715217. Additionally, we have a few brackets for slide out awnings like item # LC795354 but they are specific to Solera models. Either way I would need to know what model of awning you have to confirm the right brackets for you. If you could email me this information directly or comment below I would be happy to help.
As far as... view full answer...
Hello Bill. Looking thru all of the manufacturer's literature on this Klauber K012850300 motor, they do not list a specific strength for the sheer pin. Replacement parts are generally just linked to the motor assembly itself and those kind of specs can be hard to find, if they even exist at all. That said, we unfortunately do not carry a replacement pin for your klauber motor, so I suggest that you try contacting the manufacturer (Lippert Components) to see if they can offer you anything. view full answer...
Thanks for the kind words, Jack!
I typically recommend using the higher rated SumoSprings when it comes to motorhome just because they are heavier and the SumoSprings won't engage unless needed. This means for your 2020 Thor Quantum CR24 motorhome you need the following:
- Front # SSF-106-47
- Rear # SSR-338-54
Attached are some installation videos for you to check out! view full answer...
Hey Kenneth, yes the Solera Slide Out Awning part # LCV000251461 that you referenced does come with all brackets needed to install. It even comes with the awning rail that installs above the slide out that the awning slips into. view full answer...
Hey Mike, since they do not make a shallower slide topper for your 24 inch slide out you'd want to go with the part # LCV000168104 which has more depth than you'd need but that wouldn't be a problem. view full answer...
Hey Justin,
If you want to email me some pictures I be happy to take a look and see if I can figure out what brand awning you have. view full answer...
Hey Jerry, great question!
Yes, if you found another slide out that is rated for only 5,000 RPM then you'll be cutting the movement of the slide just about in half. The Lippert Venture Actuator and High Speed Slide-Out Motor # LC168956 that Lippert has directed us to is rated for 9,500 RPM so your slide movement will increase a little with this option. view full answer...
Hey Kenneth, so in the 79 inch size we only have the color white with the part # LCV000163285, for the 115 inch size we have the part # LCV000251461 for black or part # LCV000163292 for white, and then for the 141 inch we have the part # LCV000163298 for white.
These do come with everything needed to install with exception of butyl tape which we offer with part # AL28FJ for a 20 foot section. view full answer...
Hey Rick, if you absolutely sure your RV would never weigh more than 18k the part # DM8550024 would work fine as it's totally safe all the way up to 18k. If you think you'll end up over that number or want some "room to grow" then I would go with the 21k version part # DM8550038 instead. view full answer...
Steve, it really depends on the size of bed that you have with your 2024 Ram 2500. If you have a 6 1/2 foot bed with the OEM prep package, then part # BWRVK3670 would be the best option. Sliding hitches are what are needed for 6 1/2 inch beds to make turns with out hitting the back of the cab. If you have the 8 foot bed with the prep package then you can use part # BWRVK3600 without issue. I have also included a FAQ on 5th wheel towing for reference. view full answer...