Hi Joe,
So you just need to know if the valve you are replacing slid over your pipe or into your pipe, and I'll go over how for you.
If both ends of your waste valve slid into your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black Water Tank - 3" Spigot to 3" Spigot # T40A.
If both ends of your waste valve slid over your sewer pipe you will need the Valterra Bladex Waste Valve for RV Black Water Tank - 3" Hub to 3" Hub # T40B.
If one end of your waste valve slid... view full answer...
Hey Lance great question, but the main difference between the Double RV Waste Valves # T68 and the Double RV Waste Valves # T68C is that # T68 has a 3" hub and a 1 1/2" hub, and # T68C has a 3" hub and a 1 1/2" spigot. Other than that, they are the same. view full answer...
Hey Bryan,
Yes, you can take apart the bolts holding the two valves together on the Double RV Waste Valves - Elbow - Rotating - 3" and 1-1/2" Hubs to 3" Spigot # T81.
The actual valve portion is meant to be replaceable so taking them apart is essentially the same thing (without replacing the valve, of course). view full answer...
Yes, the Camco RV Wastewater Tank Replacement Valve # CAM39513 is threaded.
Another option is the Valterra Bladex Waste Valve # T1003VP, which like the Camco is a manual single waste valve with a 3" diameter. view full answer...
Hi Tony,
Yes, with the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank - 3" Hub to 3" Spigot # E40-8 the cable valves be open and relocate the electric valve on exposed sewer line under trailer. view full answer...
Hey Shaun so there isn't a way to adjust the valve tighter but it does seem like yours maybe has a cable problem where it's not fully closing. I would check to make sure the handle is fully able to push in and there isn't something causing it to not be able to go all the way in. Otherwise only solution is to replace the valve. view full answer...
The LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank # 34466N11AB36GM is the best replacement for your 310115. This also fits a 1-1/2" pipe and has the same 36" cable length. view full answer...
Hey Frank,
From what I can find the 129147-02-000 cross references over to the Valterra T40H which doesn't come with the cable, but I'm assuming you'd prefer to swap out to all new hardware as well. For this and the gray waste valve you can use the Valterra Waste Valve Bodies w/ Flexible Cables for RV Black Water and Gray Water Tanks # TC1372. These will both come with 72" long cables to open and close the gates. If you unbolt the old valves you can easily swap in the new ones instead... view full answer...
No, I am sorry there is not. You can try using a glove or a dry towel to get some better leverage, but I don't recommend using any tools to open the Valterra RV Waste Valve Cap item # T1020 as it is made of plastic. view full answer...
Hello Christopher. I can definitely point you in the right direction. The black tank valves are generally a 3" and the gray tank valves are generally the 1-1/2". We have both sizes available, and they can be ordered with cables ranging from 36" long up to 120" long. The 48" cables are a popular option, so for your black water you can use part # 34466N4AB48GMA and for gray water part # 34466N11AB48GMA. I do not have a way to look up your RV to know exactly what size valve or length cable... view full answer...
We don't have a way of knowing what your exact setup is, but I'm guessing you have waste valves with a long cable on your 2019 Keystone Raptor 355TS. The # VAL22RB and # VAL54MB you were looking at will work as a replacement if you want a 120" cable. The cable can be cut down to whatever size you need and will allow you to place the handle wherever you want. If you're fine with short handles at the valves you can use the # T1001VP and # T1003VP as well. view full answer...
Hello Gerry. The hub portion of the Valterra Bladex Waste Valve # T40B is 1-1/2" deep. Overall, the valve itself is a bit over 5" deep. You would want the valve to be positioned so it is easily accessible, but it does not protrude from the side of the camper. I really can't give you an exact number for like how many inches of pipe to cut off. I would take the valve and just dry fit it to the pipe to see how it is positioned and how it looks. You can then cut the pipe as needed. Replacing... view full answer...
It's hard to say yes without knowing what it is you're replacing. The LaSalle Bristol RV Sewer Hub with Flange item # 34466V13MT you were looking at bolts onto your black-water waste valve and provides a 3" MPT fitting with threads. If you don't need the threads you can use the LaSalle Bristol RV Sewer Slip Hub with Flange - 3" item # 34466V13.
If this doesn't answer your question feel free to email me directly a couple pictures of the piece you broke so I can get a better understanding... view full answer...
Good morning, Gerard. The Valterra RV Sewer Slip Hub with Flange # T1005 does not come with a gasket. It does seem like it should, so I can't really disagree with you, but that is just how the manufacturer sells this particular part. It is purely just the replacement hub and flange. We do offer gaskets though if you need new ones:
- Replacement Seals and Hardware for 3" Valterra Waste Valves Item # T1003-7VP view full answer...
Hi Chris,
You can replace just the city water inlet, you don't have to replace the entire thing with the # A01-2004BKVP you mentioned.
You'll need to find the right size and fitting, however, such as the Valterra RV City Water Inlet - 2-3/4" Metal Flange - Brass FPT # A01-0171LFVP. This part has a 1/2" FPT brass check valve but also includes an adapter for an MPT connection and has a 2-3/4" diameter flange.
I have added a link below to all of our city water inlets which you can filter... view full answer...
I'm not seeing where it states you can't use the Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" # WM8001 with your 2021 Freightliner S2RV chassis, but in any case I'd just recommend using the Wheel Masters 2-Hose Inflation Kit # WM8002 with the Wheel Masters Tire Pressure Valve Extenders # WM802990.
These hose inflators will work fine with your Freightliner S2RV chassis, measure 13" long, and the 90° extenders have an overall length of 1 1/2" with a 1" long bend.
These sound like... view full answer...
Hey Scott, I attached a link to this page that has all of the RV wye connections we offer that have 3 inch diameters on all sides of the connections like for example the part # CAM39812 which has bayonet style connections. view full answer...
It's going to be easier to place the gaskets on the pipe and slide the Camco RV Wastewater Tank Replacement Valve # CAM39513 in between.
If you can't get the gaskets to stay in place the what I recommend doing is taking a small piece of tape to keep them in place until you can get the Camco valve started. Once the valve is started you should be able to remove your tape and slide the valve the rest of the way before installing the bolts and nuts. view full answer...
When you winterize your trailer you should be draining the tanks before you bypass the water heater so there wouldn't really be any pressure to damage the # 37262255. Regardless, it should hold up to any pressure in the water line. view full answer...
The flow through sensors # TM66FR included in the TireMinder A1AS TPMS for RVs and Trailers w Signal Booster # TM86FR can be used on higher quality rubber, steel, chrome, or nickel valve stems that are rated. Lower quality rubber valve stems can bend and flex and with the weight of the sensors on them can eventually wear the rubber enough for a leak or complete failure. This is why TireMinder recommends switch to a sturdy metal valve stem to avoid any issues.
If you look at TireMinder's... view full answer...
Go To Results