We do have the length of the receiver for you of the Curt Front Mount Trailer Hitch Receiver # 31043 that fits your 1999 Chevy Suburban 2500 with RWD.
As you can see in the accompanying photo, the measurement from the front of the crosstube to the end of the receiver is 7-1/4 inches.
I have added a link to the instructions for you to check out of the Curt Front Mount Trailer Hitch Receiver # 31043. view full answer...
I did some research on the 2004 Suburban models, and I was not able to find any specific weight distribution capacity for you. Typically, the vehicle towing capacity both with and without weight distribution will be listed in the vehicle manual, or this would also be something on which you could contact the dealer. We have an informational article, see link, that explains many of the factors to be considered when using and selecting a weight distribution system.
The hitches we offer for... view full answer...
Yes, the Chain Hangers for Curt Weight Distribution Systems # C17005 that you referenced could be used on a 12k rated WD system. Curt offer either a 10k system part # 17302 or a 15k system # C17333 that this would work great with.
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached an FAQ on... view full answer...
Replacement filter # CAM40621 is designed for Camco water filter # CAM40631. The filter measures 9-3/4 inches long by 2-1/2 inches in diameter (2.6 inches at the end caps). The cci-10-clw filter you need is readily available if these dimensions are not a match. view full answer...
With combination products like the Lynx wheel and ST205/75R15 tire # LHAW320 the lower-rated of the two component parts determines overall capacity. This tire can handle 2150-lbs at its rated 65-psi pressure but the wheel itself is indeed rated for less weight, 1820-lbs, so that is the overall capacity of the combination item.
You want to choose wheels and tires to match the trailer's GVWR (gross vehicle weight rating), not its dry weight, since that is the most it can weigh and the weight... view full answer...
Absolutely!
From the top of the Stromberg Carlson Electric Trailer Jack # SC63VR to the mounting flange is 21-1/4" and from the front of the jack to the tube is 5-5/8" as shown in the included diagram.
I included a video of the # SC63VR for you to take a look at. view full answer...
The 3 inch inlet/outlet diameter on the MagnaFlow Y-Pipe # MF10798 is the outer diameter. Since this is a custom installation I recommend having a muffler shop perform the installation unless you have experience with exhaust systems. view full answer...
The inner diameter of the bearing that comes with the Replacement Bearing Kit # BD500251 is 1/2 inch. The outer diameter is 1 inch and the thickness is 0.35 of an inch. view full answer...
On the Carr Hitch Mounted Step for 2-Inch Trailer Hitches # CARR183032 when the flag-emblem step is unfolded to its step-on position that tread surface will be approximately 3/4-inch below the bottom of the receiver tube and the bottom of the step's shank portion that fits into the tube, as shown in the linked image.
The step surface measures 5-inches long x 2-1/2-inches wide. The step is Made in USA and caries a limited lifetime warranty from Carr. view full answer...
Yes, there is! To add a front hitch to your 2018 Chevy Suburban, I recommend the Curt item # C31073. This front mounted hitch is custom fit and bolts to your Chevy with included hardware. This hitch has a 2" receiver, with a 5,000 lbs towing capacity, and a 500 lbs vertical load limit.
Please note that the Curt item # C31073 will not fit the Suburban's with the Z71 trim package. I have linked the installation instructions below so you can see how to get this hitch installed. view full answer...
A lifted vehicle like your 2007 Chevrolet Suburban 1500 LT may simply need a different shank component, like # C17123 for example, to allow proper installation and operation of a weight distribution hitch (WDH) like the Equal-i-zer # EQ37100ET. All of these shank parts from the various manufacturers are standardized so you can choose the shank with the right amount of height drop to keep your hitched travel trailer level, even if it is from a different brand. All WD shanks are linked for... view full answer...
The Malone AirFlow2 roof rack system for the 2010 Chevrolet Suburban, part # MPG216, is itself is rated for a maximum load capacity of 165-lbs. This is the average weight capacity for aftermarket racks.
It is still a good idea to check your Suburban owner's manual for the roof weight capacity of your specific vehicle which could be different than the rack's. If they have different ratings, then the lower rating becomes the overall limit.
This rack uses square steel load bars which are... view full answer...
The Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs # JET-3755 (Black) and # JET-3555 (White) both measure 23 inches from the mounting plate to the top of the jack.
I have added links to some video reviews for you to check out as well. view full answer...
The Edge Clamp Feet # TH79SC used for the Thule Edge roof rack on your 2023 Chevy Suburban measures 3-1/2"tall including the rubber foot pad that comes with the fit kit. Since you have a clearance height of 5-1/2" you'll have a few inches of breathing room with this setup!
Here are the parts you need for the Edge Flush Rail roof rack:
WingBar Edge Crossbars - Black # TH76FE or Silver # TH28RE
Edge Flush Rail Feet - # TH89SC
Fit Kit - # TH95JW
Lock Core Kit - # TH450400 (optional)
If... view full answer...
The Malone AirFlow2 # MPG217 will work with your Roofnest Falcon XL on your 2011 Chevy Suburban only if your total weight is less than 165 pounds. Also, as far as fitting the crossbars of the AirFlow2, your tent will fit as long as the clamps/mounting hardware can fit a crossbar with measurements of 3 inches wide x 1 inch tall. I recommend measuring the maximum dimensions of the clamps/mounting hardware of your Roofnest Falcon XL.
If you need an option with a higher weight capacity for... view full answer...
I spoke to my contact at Curt and he informed me that from the center of the mounting holes that are on the mounting bracket on top of the hitch opening to the end of the opening measures 1-1/2 inches. view full answer...
The Ultra-Fab Motorcycle Carrier # UF48-979033 has a 500-lb load rating so it is up to the task of transporting your 2012 BMW that weighs 400-lbs.
The hitch on your 2004 Chevrolet Suburban needs to have a tongue weight (TW) rating high enough for the combined weight of your bike and the carrier that will hold it. The Ultra-Fab carrier weighs about 50-lbs, so together with your 400-lb motorcycle, you're looking at a total load on the hitch of approximately 450-lbs.
The lowest-rated hitch... view full answer...