The largest portable toilet seat that we carry is the Dometic Portable Camping Seat which has a 5 gallon tank and comes with a Gray Base # DOM44FR.
The seat itself is 13-1/4" long and the cutout is 8-3/4" x 7-1/4". According to my research it is regularly among the top picks for portable toilets in 2020. view full answer...
The power wire of the Tow Ready Custom Wiring Kit # 118480 that you referenced is 12 gauge.
I attached an install video, installation instructions and an FAQ article on routing power wires for converters like this for you to check out also. view full answer...
The inside to inside flange to flange distance of the # DT85MR Draw-Tite Class III hitch is 44 inches. Each mounting flange has 3 holes, the center hole is 2.87 inches from the mounting hole closest to the receiver tube, and the center hole and the forward-most hole are 6.59 inches apart. The hole spacing dimensioned are measured center to center. I've provided a photo showing these dimensions.
The # DT85MR is a confirmed fit for the 2021 Nissan Rogue. If you'll be using the hitch for... view full answer...
The Malone Runway Bike Rack # MPG2130 has 2 hitch pin locations to allow you to determine which will best fit your 2014 Nissan Rogue. From the first center hitch pin to upright bar is 7-3/8". The second center hitch pin to upright bar is 9-3/8"
The etrailer Trailer Hitch Receiver # e98846 has a 4-1/2" hitch pin center hole to bumper measurement on your Rogue. So you will have either a 2-7/8" or 4-7/8" clearance from the bumper to the upright bar on the Malone rack.
I recommend securing... view full answer...
The Access HD Aluminum Treadplate Truck Bed Storage Pockets are constructed of aluminum treadplate that's right about 1/8 inch thick. Using one pocket on each side would take up about 1/4 of an inch or so of the distance between the wheel wells.
Measure the current distance between your wheel wells, and subtract about 1/4 of an inch, this should give you the available space between the wells if the pockets were used. view full answer...
I went out to the warehouse and measured the Peterson Replacement Lens, item # 440-15R, and the bolt hole pattern is 3-3/4 inches square, so it should work nicely as a replacement for your Premier brand trailer lights with 3-3/4 inch bolt pattern.
At the right I have posted a photo with the measurements for you to see. view full answer...
Although we haven't installed the Draw-Tite # 36542 Class II hitch on a 2016 Rogue, we have installed one on a 2015 model, where we found the hitch pin hole to rear of bumper distance was 5-1/2 inches.
Since the 2015 and 2016 are of the same generation, and the rear of the vehicle hasn't been modified from the 2015 model year, it would be very safe to say that measurement didn't change for the 2016 model year. view full answer...
Congrats on the new car. We haven't heard about any issues with the kick sensor for the rear hatch being affected by the etrailer Hitch item # e93ZR. Typically what happens is you lose the ability to use the kick feature right around the 2" receiver. You'll need to move to the left or right of it.
The etrailer Hitch item # e93ZR is confirmed to fit your 2023 Nissan Rogue Platinum. It is custom fit and bolts to your Nissan with included hardware. I have attached an installation video below.... view full answer...
To add a hitch to a 2023 Nissan Rogue Platinum, I recommend the etrailer Hitch item # e93ZR. It is custom fit and bolts to your Nissan with included hardware. I have attached an installation video below along with a couple of pictures so you can see what this hitch looks like installed.
If you are planning on towing you will also need a wiring harness item # C44ER and a ball mount kit item # C45534.
I also recommend using the No-Drill Mount Bracket item # 18136 and the item # C42CR to... view full answer...
The weight of the trailer hitch receiver on your 2017 Nissan Rogue will not count towards your tongue weight (TW). Only the weight of your bike rack and bikes will. Therefore, you will need to make sure that weight of your bikes and bike rack do not exceed 110 lbs while on the back of your Rogue.
For a trailer hitch receiver, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75902. For a bike rack, I recommend the Swagman XTC-2 2-Bike Platform Rack part # S64670 which is... view full answer...
The dimensions of Thule Canyon # TH859XT rack are 49" long x 40" wide x 6" tall. You can add 20 inches to the length with the extension # TH8591XT.
I attached a video review of this basket on a 2016 Nissan Rogue. view full answer...
When I looked up the owner's manual for your 2008 Nissan Rogue it said on page 9-20 that your vehicle has a max trailer weight rating of 1,500 lbs with manual mode or 1,000 lbs without manual mode. Either way your max tongue weight rating is 150 lbs.
For a trailer hitch I recommend the etrailer.com Trailer Hitch Receiver # E98846 which is a Class III hitch with a 2" receiver and is rated for 3,500 lbs max trailer weight and 525 lb tongue weight. Since these are over the ratings for your... view full answer...
The internal dimensions of the Yakima GrandTour Lo Rooftop Cargo Box part # Y46FR are 85" long (lid support to lid support) x 27.5" wide (between the latches). view full answer...
The arms on the Thule Passage 3 Bike Carrier part # TH911XT measure to be 21" long. The cradles on the arms can also be adjusted front to back so you can choose the amount of space between the bikes and away from the vehicle.
I unfortunately don't have a list of the arms for each trunk mount bike rack to compare as this is not information the manufacturer provides, we have to measure this ourselves upon request. view full answer...
For your 2022 Nissan Rogue you are going to want the Draw-Tite Max-Frame Trailer Hitch Receiver item # DT85MR. This hitch is custom fit and bolts directly to your Nissan's frame with included hardware.
If you are need of a wiring harness to control your trailer's lighting functions I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # TK76FR.
To round out your towing setup I recommend the Curt Towing Starter Kit for 2" Hitches item # C45534.... view full answer...
The mounting slot for the Thule SquareBar Evo Crossbars - Steel - 47" # TH712200 are 9 7/8 inch long and 1/2 inch wide.
To fit the Thule SquareBar Evo # TH712200 on your 2020 Nissan Rogue you will need to use Evo Raised Rail Feet # TH710401 which attach to your factory front to back roof rails.
I included a video of the Thule SquareBar Evo # TH712200 being installed on a 2016 Nissan Rogue for you to take a look at. view full answer...
The maximum tongue load is 110lbs on your 2018 Nissan Rogue per the owners manual. This means the scooter carrier you would use will need to weight less than that to be safely transported on the vehicle.
While trailer hitches like our own etrailer.com Trailer Hitch Receiver # e98846 will fit your Nissan Rogue and has a capacity up to 525lbs, that is always limited by the vehicle manufacturer's recommendations. You will want to consider a different vehicle for this specific purpose... view full answer...
I have a great aero roof rack for you but since your 2023 Nissan Rogue has the side rails there isn't an option from Thule to add a roof rack. I checked with Thule and all of the their options are for the naked roof. It does not look like they have a way to grip the side rails.
Instead, you are going to want the roof rack by Yakima and it includes the following parts:
Yakima SkyLine FX Roof Rack for Fixed Mounting Points - JetStream Aero Crossbars - Qty 2 item # Y76UV
Landing Pad 31... view full answer...
To add a hitch to your 2024 Nissan Rogue, I recommend the etrailer item # e93ZR. This hitch is custom fit and bolts to your Nissan with included hardware. This is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity and a 525 lbs maximum tongue weight.
I really like the etrailer hitch item # e93ZR because the crosstube mounts behind your rear bumper leaving only the 2" receiver exposed. This not only looks better but it helps with ground clearance.
f you are planning... view full answer...
Yes, it does! The Draw-Tite Hitch item # DT85MR has been confirmed to fit the 2024 Nissan Rogue. This hitch is custom fit and bolts to your Nissan with included hardware. This is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity and a 525 lbs maximum tongue weight.
I really like the Draw-Tite hitch item # DT85MR because the crosstube mounts behind your rear bumper leaving only the 2" receiver exposed. This not only looks better but it helps with ground clearance.
If... view full answer...
Go To Results