Expert Answers about Volkswagen Rabbit
- Is Trimming Required for Installation of the 2008 Volkswagen Rabbit Hitch # 11074
- No, installation of the Curt Class I Trailer Hitch, item # 11074, on a 2008 Volkswagen Rabbit does not require trimming of the rear bumper fascia. I have included a link to the installation instructions for you to review.
To complete your Class I Towing setup you may also want to consider the following items.
Vehicle Wiring # 119250KIT
1-7/8 inch hitch ball # 19256
2 inch hitch ball # 19258
Pin and clip # PC2
view full answer... - How to Prevent Exhaust Components from Contacting the Trailer Hitch
- It is not uncommon for the exhaust components on a vehicle to come in contact with an aftermarket trailer hitch. The reason for this is that the placement of the exhaust components from the manufacturer are relative and not exact which means they will all be the same general location but may be slightly tilted or hanging an 1" or so in one direction or another from vehicle to vehicle.
An easy way to fix this would be to just bend the hangers slightly with a bit of heat and a pry bar. I...
view full answer... - Why is a Stabilizing Strap Recommended on Curt Hitches and what is Meant by Non-Trailer Load
- Non-trailer loads are hitch accessories like bike racks and cargo carriers. Basically anything that is not a trailer that you could put on a hitch. Curt recommends you use a Curt Trailer Hitch Support Strap # 18050 to help prevent excessive jarring on the hitch from bumps.
Basically you will attach one of the strap to the hitch accessory and the other end to the trunk lid of your vehicle and the support will help brace the setup to prevent excessive jarring of your hitch setup.
Check...
view full answer... - Is Trimming of the Foam Absorber Required for the Curt Hitch On a 2010 Mini Cooper Convertible
- The Curt Trailer Hitch Receiver part # C11160 is a fit for a 2010 Mini Cooper Convertible with single exhaust. In regards to installation, there is a metal divider panel that will need to be removed if present. Once removed, this should then make for the needed space to trim the foam absorber. I have attached a photo which should help explain this.
view full answer... - Is Fascia Trimming Required to InstallCurt Trailer Hitch C11074 on a 2008 Volkswagen Rabbit
- There is no fascia trimming required to install Curt trailer hitch # C11074 on your 2008 Volkswagen Rabbit. I have linked a video showing an example installation for you.
The Draw-Tite part # 24825 is a Class I hitch like the Curt; it does not require fascia trimming as it sits below the fascia.
view full answer... - Installation Instructions for Wiring a 2008 Volkswagen Rabbit to Tow a Trailer
- Due to the MX (Multi-Plexed) wiring system on your 2008 Rabbit, you will need the Tekonsha Wiring Kit, # 119250KIT, to add trailer wiring to your vehicle. This kit actually connects without splicing into your current wires, they just clip on and can read the signals through the wires.
On the 2008 VW Rabbit, you will need to find the circuit that contains 12-volt brake and taillight functions and does not have the turn function on that wire. Attach the red stop wire from the # 119250KIT...
view full answer... - Where Does the Rhino-Rack Roof Rack Install on a 2007 Volkswagen Rabbit 3-Door Hatchback
- With the Rhino-Rack roof rack clamps, # DK064, you will first need to position the front clamp which will be approximately 9-27/32 inches forward of the center of the upright support directly rearward of the doors. Take a look at the picture that illustrates what I mean. That measurement will be where the center of the foot will be on the roof.
You will then measure from that point straight back 27-9/16 inches. This is where the center of the rear foot will be. The drawing of the vehicle...
view full answer...
Go To Results