Expert Answers about Infiniti QX50

• Should there be a Gap Between Rubber Strip and End of Rola Roof Rack Crossbar
• You do want the top rubber strip on the tops of the crossbars to cover the whole channel in Rola Sport Series Roof Rack with RBU Mounting System for Raised, Factory Side Rails - 47" Long Item # RBU47. There are a few things that can cause the strip to appear too short. It is possible that temperature changes, if extreme enough, could cause the strip to expand or contract. The shipping process can do all sorts of things to products so I imagine it is possible for the bars to rub on something...
  view full answer...


• Is Wiring Harness Needed for 2014 Infiniti QX60?
• You would need wiring harness # 119250KIT for your 2014 Infiniti QX60 only to power lights on an accessory that would go into your vehicle's trailer hitch. The hitch available for your '14 Infiniti only has a Class I hitch available, the Curt # C11510, and according to your owner's manual, this vehicle should not be used for towing so the wiring would only be needed if you were to use a cargo carrier, for example, that had lights that needed to be plugged in. The harness that fits your...
  view full answer...


• Replacing Cabin Air Filter in 2019 Infiniti QX50
• The PTC Custom Fit Cabin Air Filter # 3513696 will fit your 2019 Infiniti QX50, and to install it you do need to actually remove the entire glove box. This will require you to pull it up from its hinges on the bottom, and undo a cord/strap on the left. You will then need to unscrew seven Phillip screws, which will then allow you to remove the cover.
  view full answer...


• Installation of Tekonsha 118796 Wiring Harness on 2020 Infiniti QX50
• The installation of the Tekonsha # 118796 does require the removal of the tail lights from the vehicle but it won't require any cutting into the wires; once that has been completed you can access the rear of the lights where the plugs can be teed into. You will need to open the tail gate and access the bolts that will allow you to remove the tail light assembly. I've linked a copy of the installation instructions for you to check out that does a pretty good job of showing how this can...
  view full answer...


• Can the Draw-Tite Trailer Hitch for a 2020 Infiniti QX50 Be Used to Tow a Trailer
• The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76240 which is a fit for a 2020 Infiniti QX50 has a 4,000 lb gross trailer weight rating. That said, if the vehicle is rated lower that's the figured you'll need to abide by. This figure can be found in your owner's manual. Therefore, so long as the weight of the trailer and cargo is below the tow capacity of the vehicle (check owner's manual) you'll be good to go. Please note, in order to complete your setup you'll also need a trailer...
  view full answer...


• Can Curt Trailer Wiring C56236 Install in Vehicle with LED Taillights
• The Curt wiring harness part # C56236 can be used on a vehicle with LED taillights because it draws all of the amperage needed for illuminating the trailer lights from the vehicle battery. You need to use the power kit part # C55152 to make the connection to the vehicle battery. Basically it just uses the taillight circuits as signal wires and draws all the amperage from the battery.
  view full answer...


• Which Tires Should Chains be Installed on with AWD 2017 Infiniti QX50
• I took a look at the online version of the owner's manual for your 2017 Infiniti QX50. Under the "Tire Chains" section it actually states that snow chains should only be used on the rear tires and not on the front tires for your vehicle. The vehicle's owner's manual is always the best place to check when determining which tires chains can be used on as it will vary from vehicle to vehicle, regardless of its drivetrain. Within the Tire Chain section of your manual it also says to only...
  view full answer...