It will work with both. The Curt T-Connector Vehicle Wiring Harness item # C56404 sends the signals from your tail lights to the converter box that actually powers your trailer's lights. The direct line from the battery powers both LED and incandescent bulbs.
The Curt T-Connector Vehicle Wiring Harness item # C56404 is confirmed to fit a 2017 Audi Q5 with the factory supplied connector located in your cargo compartment.
If you do not have the factory connector you'll have to use the... view full answer...
The Curt Trailer Hitch # C13331 that fits on the 2018-2020 Audi Q5 will sit approximately 15" from the ground to the top of the receiver- so it will be around 13" from the bottom of the receiver. This will also depend on whether or not the vehicle is carrying passengers and cargo, the tire size or has a trailer connected to it- since there will be some squat in those circumstances.
If you need a wiring harness to power trailer lights I recommend using the Tekonsha Zero Contact Interface... view full answer...
The Rhino-Rack Ski and Fishing Rod Carrier # RR572 can mount to roof rack crossbars in two ways, with the included universal-fit clamps that let it attach to almost any type of roof rack bar, and also with the T-Bolt hardware that slides into the C-channel slot is on the top of many types of crossbar.
I went to our warehouse and measured the T-bolt in this carrier and the head measures 3/4 x 3/4-inches. view full answer...
The Fulton strap part # FWS20HD0200 that you referenced would work great for what you mentioned. This is 20 feet long and has a 4,000 lb capacity. With winches and straps you'd generally only need the capacity to be 50 percent of the total weight of the boat so a 4,000 lb weight rated strap would easily have enough capacity for a 5,000 lb boat view full answer...
Yes, the Draw Tite Hitch part # 75940 that you referenced is a confirmed fit for your 2011 Audi Q5. This hitch does replace a support beam of your rear bumper but does not require any cutting or drilling aside from that.
I attached a picture from the instructions that shows this step for you to check out as well. view full answer...
The 53" Thule WingBar Evo Crossbars, Black # TH711420 and Silver # TH711400, have channels on the bottom which measure 9-3/4" on either side. This means that the space between the channels is 33-1/2". As long as you don't have less than that you're good to go! view full answer...
To purchase a Stealth Hitch without the wiring, for your 2014 Audi Q5, you will want the Stealth Hitches Hidden Rack Receiver item # 391AUDQ509. The ball mount is available for purchase separately item # 391BMU5S but not the bracket that holds onto the wiring harness. You will also need the 2" Hitch Ball item # 63845.
Stealth Hitch makes it difficult and not cost effective to piece it out. There's no kits other than the entire Towing Kit w/ Ball Mount and Trailer Wiring item # 391CONVR5. view full answer...
The weight of the Draw-Tite Trailer Hitch Receiver # 75940 you were looking at for your 2016 Audi Q5 is right at 42lbs.
I included a video of the # 75940 being installed on a 2016 Audi Q5 for you to take a look at. view full answer...
I contacted our representative at Draw-Tite about the # 75940 hitch and asked about the ground clearance on your 2011 Audi Q5. I was told that they do not have specific measurements on ground clearance as it can vary from different model years and sub models of each vehicle.
He did inform me that the hitch sits about 1 inch away from the bumper fascia, so what you can do is measure from the bottom edge of the bumper down about 3-1/2 inches. This measurement will give you an idea of where... view full answer...
The thread size of the Replacement M8 T-Bolt for Thule Roof Rack Gutter Feet # 853-0782 that you referenced is the same as what this replaces. So this would thread in place of what you have easily. view full answer...
Go To Results