Expert Answers about Isuzu Pickup

• Parts Needed To Add 7-Way Connector To 1990 Izusu NPR Truck
• Absolutely! To install a 7-way connector on your 1990 Isuzu NPR you will first need to install a 4-way connector. Since there is not a custom 4-way connector harness you will need to use the Upgraded Modulite Vehicle Wiring Harness Kit # C59236 which includes a circuit tester to verify the functions of your factory wiring to make sure you make the correct connections. The 4-way connector will wire as follows: White wire to the vehicles frame Red wire to brake light Green wire to passenger...
  view full answer...


• What License Plate Lights Are Available That Are Waterproof
• The light on the Optronics License Plate Light # LP55CB is an incandescent light and it is not waterproof. I do have six license plate lights that are submersible (waterproof) and they are all incandescent lights. I am sending a link to the page that will show the six choices available.
  view full answer...


• Availability of License Plate Bracket to Attach to Westing SureStep Bumper
• The Westin SureStep Replacement Bumper part # 61001-95700 that you referenced would use a standard license plate frame like the part # CR15350. I attached a picture that shows where you'll attach the bracket to.
  view full answer...


• What Is The Height On The Rubber Spring In Timbren Rear Suspension Enhancement System # TIR100
• In the Timbren Rear Suspension Enhancement System, part # TIR100, the height of the hollow rubber spring is 3-3/4 inches and the width is 3-3/8 inches. I am including a picture that will show where the measurements are taken on the spring. I am including a link to the installation instructions on the Timbren suspension.
  view full answer...


• Can the Class IV Weld-On Ultra Frame Trailer Hitch be Used on a 1987 Isuzu Pickup
• The Class IV Weld-On Ultra Frame Trailer Hitch Receiver by Draw-Tite, Hidden Hitch and Reese, item # 41990, is a weld on application and it is possible that the hitch could work on your vehicle. You would need to measure the width of your vehicle frame and consult a qualified Weldor to determine if the frame on your vehicle is strong enough to weld the hitch to. He will also need to determine if the frame configuration will accept the hitch in the proper orientation for towing. Along with...
  view full answer...


• Does the Hydrastar Marine Actuator Work w/ the RedArc Tow Pro Elite Brake Controller?
• Yes, the Hydrastar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness item # HS381-9065 will work with the Redarc Tow-Pro Elite Trailer Brake Controller item # RED44FR. The Tow-Pro Elite works with electric over hydraulic brakes.
  view full answer...


• Trailer Hitch Options for a 1995 Isuzu Pickup
• There are universal style trailer hitches that you may be able to adapt to your 1995 Isuzu Pickup, but, trailer hitch manufacturers do not make a custom fit trailer hitch for that truck. Universal trailer hitches like the Draw-Tite Weld-on Ultra Frame Hitch, # 41990-07, have mounting brackets that fit a variety of different frame styles and are adjustable to fit different frame widths, but they do require welding to install. Because this is a universal application, it would be up to the...
  view full answer...


• What is the Length of Roadmaster Base Plate to Tow Ready Tow Bar Adapter # RM-025
• I went out and measured the distance between where the legs of the tow bar attach on the Roadmaster Base Plate to Tow Ready Tow Bar Adapter, # RM-025, and the on center measurement is 31 inches. The distance between the mounting bolt holes that attach to the vehicle base plates is 28-1/2 inches on center. If you are looking for the overall length it is approximately 34 inches.
  view full answer...


• Where are the Shorter and Longer Bolts Installed in the Base Plate Kit # 607-4
• I checked the install instructions for the # 607-4 and step 2 requires the 1-1/4 inch long bolts: Starting with the drivers side, remove the two steering unit bolts behind the bumper attachment box. Bolt a ¼” x 3”x 5 3/8” rear mounting plate to the frame as illustrated using the two supplied 10mm x 1.25 x 110mm bolts, hardware. And then step 5 uses the longer 1-1/2 inch bolts: Now, bolt the rear of the brace to the flat mounting plate using two ½” x 1½” bolts, flat washers, lock washers...
  view full answer...