There are a few options for the different trim levels on a 2017 Chrysler Pacifica and these will have different connectors, so you will need to verify which you have first. I have these listed below.
LX and Touring:
Tekonsha T-One Vehicle Wiring Harness # 118723
Limited, Touring L, Touring Plus, and Touring L Plus:
Tekonsha T-One Vehicle Wiring Harness # 118712
Hybrid Models:
Tekonsha ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT
If you have an LX or Touring model, you should... view full answer...
The issue you are having with the # e98903 hitch holes not lining up correctly on your 2018 Chrysler Pacifica is likely due to the hitch being bent. Sometimes a hitch gets slightly bent during shipping, which may result in misalignment during installation.
I would inspect the hitch and make sure there are no cracks, chipped paint, or stress marks. These are signs that the hitch may have flexed enough to be considered unsafe and should be replaced. Assuming that is not the case, the trailer... view full answer...
According to the online owner's manual for your 2021 Chrysler Pacifica you will only install the Titan Chain Alloy Snow Tire Chains # TC2319 on the front set of tires. Since that is specifically noted in the manual I wouldn't install them on the rear set.
Attached is an installation video of these chains on a 2020 Pacifica for you to check out. view full answer...
The answer to your first question can get pretty involved, but in summary purchasers of aftermarket vehicle products are protected by the Magnussen-Moss Warranty Act which states that installing a hitch won't void a vehicle warranty unless the vehicle manufacturer can prove that the aftermarket part directly caused the failure. You can install the Curt Class III # C13383 hitch with no worries.
Curt tells me that they've received no report of the hitch installation having any effect on... view full answer...
That is correct.
To install the Curt Trailer Hitch Receiver # C29UR on your 2018 Chrysler Pacifica Hybrid you will need to remove two the exhaust hangers from the rubber isolators, and support the exhaust to make sure it does not get damaged. Next you will remove the heat shield you mentioned, and will need to trim it according to the included diagram.
Once the hitch is in place, you will reinstall the heat shield, and the reinstall the exhaust into the rubber isolators. You will also... view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118712 which is a fit for a 2019 Chrysler Pacifica will not have any effect on the vehicle's tail lights. Therefore, even if the in-line fuse on the power wire which leads from the converter box to the vehicle's battery blow, the vehicle's tail lights will still work just fine.
If you don't already have a trailer hitch picked out, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C65CR is what I recommend... view full answer...
If you have the factory tow package, installation of part # 42145 is very easy. There will be a connector on a wiring harness that will fit this part, it will be tucked up, maybe taped, somewhere close to the rear bumper. You will then attach the mounting bracket in a convenient location near the hitch, and it will hold the 7 way plug.
If you do not have the factory tow package, you will need the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55530. I've... view full answer...
The 4-pole trailer wiring harness you referenced, TowReady T-One Vehicle Wiring Harness # 118303, is a correct fit for your 2005 Chrysler Pacifica. This plug-in harness requires no cutting or splicing of wires since it uses T-connectors that plug in inline with the wiring to your Pacifica tail lights.
If there is a white wire with a ring terminal secured to the vehicle's metalwork behind the driver-side tail light this should remain in place. Often white wires with ring terminals are... view full answer...
For your 2017 Chrysler Pacifica the Draw Tite Hitch part # 36798 is a confirmed fit and would still allow you to use your hands free liftgate. At the very worst you might have to run your foot to either side of the hitch opening but it will still work just fine. This is a 1-1/4 inch hitch which would work just fine for you for a small trailer or bike rack, but since more accessories are made for 2 inch hitches and they have higher capacities I would recommend you go with the part # e98903... view full answer...
Installing a brake controller in your 2019 Chrysler Pacifica is going to depend on if you have the factory 7-way or no factory trailer wiring at all. If you do have the factory 7-way you can install a brake controller with just the correct wiring adapter. For example, the Tekonsha PowerTrac # 39523 brake controller requires just the Plug-In Wiring Adapter # TK93VR. You will plug in one part of the adapter to the controller and the other part to the port underneath your dash for a simple... view full answer...
Yes the Pilot brake controller part # 80550 will fit your 2020 Chrylser Pacifica with a factory 7-way with the install harness part # TK93VR. All you'd need is the install harness and the brake controller and you'd be set. view full answer...
You can check out the video that I've linked for you that will walk you through the install. As you'll see, the install involves removing and trimming an under body panel and heat shield as well as temporarily lowering the exhaust which would be very hard to do unless at least the rear of the vehicle was raised in some manner. I'd recommend using ramps or putting the rear of the vehicle up on jack stands so you can have more room to work with.
If you'll be towing with the hitch, you'll... view full answer...
When installing the Tow Ready Curt Wiring Harness # C55530, on your 2004 Chrysler Pacifica, you will need to access the fuse box under the hood on the driver side near the front of the vehicle. Next, you will insert the 20 amp fuse into position number 10 labeled Trailer Tow/Spare B3-5 (see photo). I have attached a link to the installation instructions that contains this information. view full answer...
I have recommendations for you but unfortunately, you will not have a factory plug in under your dash nor will you have a factory 7 way or 4 way at the back of your 2006 Chrysler Pacifica. This is because a factory tow package is not available for your vehicle.
However, if you are looking for the proper wiring and brake controller to tow a trailer with brakes, I have the wiring you will need to do so.
First, for a brake controller I recommend the Tekonsha Prodigy P3 Brake Controller... view full answer...
I spoke with Progressive Dynamics and they informed me that you cannot replace just the converter section of your 8735P and you would need a new panel, the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part # PD4045KA to be able to charge a lithium battery.
The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger now comes with a lithium switch. view full answer...
I have good news for you - since you have a factory 7-way in your 2020 Chrysler Pacifica you have a very simple "installation" which will require nothing more than plugging a brake controller wiring adapter into the port under the dash of your Pacifica and then plugging the brake controller into that adapter (essentially, you can think of the adapter as like an extension cord for the brake controller).
I really like the Tekonsha Prodigy P2 Trailer Brake Controller # 90885 because it is... view full answer...
The only way I know to convert 12V to 24V is to run two 12V batteries in series. I've attached a photo to show how to do the wiring for the 24V output. This shows where you would connect the positive and ground of your trolling motor. view full answer...
I attached a couple pictures that I took from the install instructions for the trailer wiring harness part # 118712 that is confirmed as a fit for your 2017 Chrysler Pacifica. In the instructions a trim panel remover tool like part # ALL648544 is recommended.
You will also need a Torx T27 socket wrench to remove the taillights.
It's the underside body panel that actually gets removed and not any of the interior pieces. view full answer...
We don't publish the torque ratings for the fasteners, because the hitch manufacturers can change them. If you look at the bottom of page 2 of the instructions (see provided link), you'll see the torque rating for both the 1/2 inch and the M12 fasteners. The links pull the instructions directly from the manufacturer's websites, so they're always current. I'll also link you to an install video for the hitch.
If you'll be using the hitch for towing, you might also be interested in the following... view full answer...
The etrailer hitch # e98903 is a confirmed fit on the 2018 Chrysler Pacifica Hybrid and it also fits the standard version. The instructions for this hitch have been sent to you in a separate link. They will be essentially identical to the instructions for Curt hitch # C13383; those instructions are linked for you here. view full answer...
Go To Results