The wiring gauges for the Redarc Tow-Pro Elite Trailer Brake Controller - 2 Braking Modes - 1 to 3 Axles - Proportional # RED44FR are as follows:
Blue: 12AWG
Black: 12AWG
Red: 14 AWG
White: 14 AWG
All wire ratings refer to the minimum required cross sectional area of copper only (not including insulation). Always use a wire gauge equal to or greater than what is specified. view full answer...
Yes. You can use the Adarac Pro Series # A4000950 with a tonneau cover like the Pace Edwards Switchblade # 311-SWCA03A25, since the Pro Series mounts using the stake pockets and the Switchblade mounts inside the bed rails.
I've linked a short review video on these parts for you to have a look at. view full answer...
If you have the Rapid Podium Feet for Thule Crossbars - Fixed Point - Qty 4, part # TH460R, and square crossbars, the last part you need for your roof rack is the fit Fit Kit for Thule Podium-Style Roof Rack Feet - 3101, part # THKIT3101. The the rubber bases for the Thule feet come with the fit kit. These feet go with the redesigned Thule square crossbars -- they have a channel on the underside of the crossbar. Your 2020 Chevrolet Colorado needs a 69" crossbar and Thule does not make a... view full answer...
For a Thule TracRac ladder rack combination to fit the bed of your 2017 Chevy Colorado along with a tonneau cover you need the following combination of parts:
- Thule TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-783
- BAK Revolver X4s Hard Tonneau Cover # BAK92VR
These fit a 6' Bed so if you have a different TracRac ladder rack with the traditional clamp-on system then there unfortunately aren't any ladder rack/tonneau cover options that fit together. view full answer...
Yes, the Demco Tabless Base Plate Kit item # DM9519319 will work with the etrailer XHD Non-Binding Tow Bar item # e94ZR. The Demco base plate kit is confirmed to fit your 2022 Chevrolet Colorado LT. It mounts where your tow hooks are currently and protrudes through the same cut outs.
Some other components needed to flat tow your Chevy Colorado are listed below:
For a wiring harness I suggest item # RM-15267, the diode kit that comes with this allows you to splice into the taillight wiring... view full answer...
The pilot light would be covered enough by components/door of the water heater to not have to worry about it igniting the gasoline while refueling unless you were directly spraying gas on door of the water heater.
The Dometic RV Water Heater - Gas and Electric - Automatic Pilot - 120 Volt - 10,000 Btu - 6 Gal Tank # DMC74FR is a WH-6GEA model so it would be a correct replacement for your current water heater. view full answer...
Yes, the Westin Platinum Series Oval Nerf Bars that fit your 2021 Chevrolet Colorado Extended Cab is found as part # 21-4005 on our site.
Attached is a review video of these bars for you to check out. view full answer...
The AirBedz part # AB42ZR that you referenced is designed to fit your 2018 Chevy Colorado's back seat with the seats folded up since it has the lower portion that goes down into the leg area. This fits the version of the truck that have the 5 foot or the 6 foot bed. view full answer...
Thank you for your purchase of the Thule TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-783 and the Access Vanish Roll-Up Tonneau Cover # A92359 for your GMC Canyon or Chevy Colorado with 6-foot bed.
Often a tonneau cover and ladder rack will require installation at (or near) common mounting points on a pickup and this means that some combinations rack and cover will not be compatible.
The only specific tonneau cover we know to be compatible with the TracRac SR Ladder Rack system... view full answer...
I do have an option for you but Blue Ox does not offer a base plate kit for a 2022 Chevrolet Colorado ZR2 Bison. The only option we do have for this vehicle is the Roadmaster Direct-Connect Base Plate Kit part # RM33VR. That said, you can use this base plate kit with a Blue Ox tow bar like the Blue Ox Ascent Non-Binding Tow Bar part # BX4370 when you add an adapter, the Roadmaster Adapter Kit for Blue Ox Motorhome Mounted Tow Bars pat # RO64FR. view full answer...
I took a look at the owner's manual for a 2019 Chevy Colorado and on page 315 of the online version it states "Use of a shield mounted in front of the vehicle grille guard could restrict airflow and cause damage to the transmission ... If using a shield, only use one that attaches to the towing vehicle."
Due to this I strongly recommend using the Roadmaster Tow Defender Protective Screening # RM-4750 which has a mesh screen to protect the front of your Colorado and still provide air to... view full answer...
If you're wanting the installation instructions for the Blue Ox Base Plate Kit # BLU93FR that you were looking at then I've attached them below. As for the light kit, Blue Ox doesn't have a plug-in option for your Colorado so you'll have to go with a Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267.
The battery will need to be disconnected in order to flat tow your Colorado so I also recommend picking up the Roadmaster Battery Disconnect # RM-766 to make disconnecting/connecting... view full answer...
We do indeed offer hitch options for the 2022 Chevy Colorado.
Of the available options, I'd recommend the US made etrailer brand Class III hitch, part # e98909. The hitch has a 8000 lb towing/800 lb tongue weight capacity, which actually exceeds the towing capacity of the truck itself, so there's no doubt that the hitch is tough.
For a trailer wiring harness and trailer connector that provides both a 7-way and a 4 pole trailer connector, use part # HM40975-11998. For a ball mount, use... view full answer...
Yes, your Blue Ox Aventa II tow bar part BX7335 will fit with the Blue Ox Base Plate Kit BX1721 you're asking about.
The BX1721 was discontinued back in 2021 though so unless you're purchasing it second-hand you'll need the Blue Ox Base Plate Kit # BLU93FR instead for your 2018 Chevy Colorado, which also works with the Aventa II tow bar. view full answer...
The great thing about the Viking Solutions Stack Rack II # 310-VSR201 is that both baskets have a maximum weight capacity of 150 pounds (300 combined). If you just want to store cargo in the upper (smaller) basket of the carrier in order to ensure visibility of your vehicle's license plate, that option will work on your 2020 Chevrolet Colorado. However, there still might be some partial blockage of your license plate do to carrier bars on the bottom basket.
If you need a hitch to mount... view full answer...
Yes, the Toolbox Mount Kit for Thule TracRac TracONE Truck Bed Ladder Racks part # TH41000 will work with a T-Rac Pro2 Truck Bed Ladder Rack part # TH37002XT-EX which is a confirmed fit for your 2017 Chevrolet Colorado. I spoke to my contact at Thule to confirm this.
However, if you are purchasing the T-Rac Pro2 Truck Bed Ladder Rack new then you will not need the toolbox mounting kit as it is included with the rack. view full answer...
You won't cut the item # RRVA150B-2 59" crossbars at all because you need the extra length to use the Hullavator item # TH898. You will need to cut the measuring strips in accordance to the new location the 59" bars will be mounted not the 49" because the cuts will be to far inside the longer legs. It has to extend at least 4" past where your standard bars would for the Hullavator's lift assist function to work properly. I looked at the instructions and there is no 32" measurement. What... view full answer...
No, the CIPA Custom Towing Mirrors # CM10300-2 will not fit your 2007 Chevrolet Colorado. instead, you'd want to use a set of universal mirrors like the CIPA Universal Towing Mirrors # CM11980-2.
These are not going to be the slide in style like what you're looking at, but will just as easily install by clamping onto your current mirrors. view full answer...
The Westin Premier Oval Nerf Bars w/ Custom Installation Kit # 22-6020-1395 you were looking at are indeed a confirmed fit for your 2011 Chevy Colorado Crew Cab. This kit fits quite a few years of the Colorado which is why Westin's instruction still show for the previous generation, but as I mentioned, I did confirm fitment for your vehicle so you won't need to worry about that.
Installation is simple with the included hardware, and no drilling will be required! view full answer...
I have a great suggestion for you. Unfortunately, there are no truck-rack system options that are easily removable when not in use. However, for a rack system that is compatible with your Bakflip MX4 Tonneau Cover, I recommend the Adarac Aluminum Series Custom Truck Bed Ladder Rack # A4001226. The Adarac Ladder Rack installs into the stake pockets and sits on top of the side of the truck beds (allowing for the clearance of the Bakflip MX4).
In addition to the Adarac Ladder Rack, I recommend... view full answer...
Go To Results