bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Mazda CX-7


  • What Is Required To Install Draw-Tite Class III 2 Inch Trailer Hitch # 75512 On A 2009 Mazda CX-7
  • There is no drilling required when installing the Draw-Tite Class III 2 Inch Trailer Hitch # 75512 on a 2009 Mazda CX-7. You will need to lower the exhaust in the rear by removing the exhaust from the rubber hangers, but it will be connected back to the hangers after the hitch is installed. I am including links to the installation instructions of the Draw-Tite hitch and a video link that will show the hitch being installed on a 2007 Mazda CX-7. Draw-Tite says an installation by a professional...
    view full answer...

  • How to Install the Michelin Stealth Windshield Wiper Blades on a 2011 Mazda CX-7
  • The Michelin Stealth Ultra Windshield Wiper Blade part # MCH8526 is a confirmed fit for the drivers side of your 2011 Mazda CX-7. If you need to replace the passenger's side you will want part # MCH8516. In order to install the wiper blades you will want to first remove the old blades by rotating the blade until it is perpendicular to the windshield and then pull downward. To install the new wiper blades you will need to rotate the connector piece on the blade and attach it onto j-hook...
    view full answer...

  • How to Install the Alpena LED Fog Litz 4 Part # ALP77160 with a Toggle Switch
  • I do have a way for you to install the Alpena LED Fog Litz 4 part # ALP77160 on your 2010 Mazda CX-7 but unfortunately I cannot recommend you use them inline with your low-beam headlights as you would likely exceed the maximum amp draw allowed for that circuit. In order to install the fog lights on your CX-7, I recommend using them with a toggle switch such as the LED Micro Bug Push Button Toggle Switch part # PL-SW28B. In order to install the fog lights with a toggle switch you will need...
    view full answer...

  • Can Rhino-Rack 2500 Series Roof Rack Be Permanently Installed on 2011 Mazda CX-7
  • The Rhino-Rack 2500 Series Roof Rack with Aero Crossbars can certainly stay installed on your 2011 Mazda CX-7 as a permanent installation. You need parts # RRVA137B-2, # RRRLKVA, and # DK289. I have attached review videos of both the 2500 Series rack system and the custom fit kit for you to see how the different components are put together and install. The rack also includes written instructions with diagrams to help you install the rack on your CX-7. The video for the fit kit shows a...
    view full answer...

  • What Will a Class III Trailer Hitch Look Like When Installed on a 2009 Mazda CX-7
  • We have several Class III trailer hitches available for the 2010 Mazda CX-7. First is the Draw-Tite Trailer Hitch, # 75512. I have included a link to the instructions and a video for this hitch as well. For the most part, only the receiver shows. The other Class III Hitch, # 13593, will have a similar appearance after it is installed. Both of these hitches, when installed, are pretty well hidden as you can see in the videos. For the most part, only the receiver shows.
    view full answer...

  • How Do You Connect 4-Way Flat Connector In Rear Cargo To Added 7-Way On a 2010 Mazda CX-7?
  • For your 4-Pole Harness # 118405 you will need to find a grommet in the rear floor where you will be able to run the connector and wiring out. If there is not one large enough for the connector you can drill an opening or cut the connector off and run the wiring out. Then you will be able to either reattach the connector or cut the 4-way connector off the 7-Way # ETBC7 and just use Heat Shrink Butt Connectors # DW05744-5 to connect the wiring. This will provide the best connection for the...
    view full answer...