When using the Curt Echo Trailer Brake Controller # C51180 you will not need a brake control wire. We specifically created the 7-Way Upgrade Kit # ETBC7L which has the 7-way which will plug into a 4-way flat and the wiring needed to run a charge line. The charge line is what will power the Curt Echo and provide power for sending to the trailers electric brakes. The Echo knows when to send power to the trailer brakes by sensing when power is sent to the brake lights on the trailer wiring... view full answer...
It sounds like you've got flush mounted rails (a matte black flush mounting "molding" that runs from front to back) on your 2019 Jeep Grand Cherokee High Altitude edition, and while they're more intended for cosmetics you can install a roof rack on this vehicle. The best combination of quality, durability and price point is the Rhino Rack Roof Rack for 2019 Jeep Cherokee, which uses parts # RRVA137B-2 , # RRRLKVA and # DK234 to provide you with the crossbars, foot pack and mounting kit... view full answer...
First you will need a Tekonsha Plug-In Wiring Adapter # 3062-P to connect to the factory tow package wiring on your 2023 Subaru Ascent. This will allow you to connect to the Redarc Tow-Pro Elite Brake Controller for Tekonsha Harness # RED63RR. The controller includes a universal Mounting Panel # 331-TPSI-001 allowing you to give it a factory appearance. view full answer...
The only locking piece that works with the 24x60 etrailer Cargo Carrier # e98874 is the Threaded Anti-Rattle Hitch Pin Lock # e99047 that you referenced. There aren't any locks for standard hardware save from using threadlocker like the part # LT37420 which makes hardware near-impossible to remove.
I'm not sure I would use the threadlocker though. Thieves tend to be opportunists so if someone is prepared enough to bring tools to steal your carrier I'm sure they would have some backup equipment... view full answer...
Since your 2020 Subaru Ascent is already equipped with a factory 7-way connector, you will not need any additional parts other than the ones included with the Curt Spectrum Brake Controller part # C51170.
There isn't a custom wiring adapter available from Curt for your Ascent, so you will need to hardwire the Spectrum controller in order to install it, or you can easily make your own adapter, using part # 3062-P.
Basically, you'll cut off the black end of this adapter (the one that matches... view full answer...
You are correct that you want to be within the weight range of a particular system and that has to do with the total tongue weight. That includes the loaded trailer tongue weight along with any cargo behind the rear axle of your truck. You want the total tongue weight to fall in the middle of the range of a weight distribution system ideally. If you travel with water tanks full, which most people don't unless you'll be dry dock camping, that will add significant weight.
For your Forest... view full answer...
When it comes to getting no power from your car to the RV battery on your 2020 Subaru Ascent it sounds like there could be a loose wire somewhere on your vehicle, or there could be dirt or debris in the pins where you would plug into the car. I would recommend using The Hook Probe Circuit Tester Kit # PTW2993 to see which wire is not getting power. This will also test each function of the plug and let you know which one is which. To find the fuse I would recommend reaching out to Subaru... view full answer...
Yes, we do have a similar pattern of tire chains like the # TC2323 that will fit your 2021 Subaru Ascent with a tire size of 245/60-18. For the correct fit, you will need the Titan Chain Alloy Snow Tire Chains # TC2317. These chains come with the same diamond-shaped pattern and include the same manganese nickel alloy construction as the # TC2323. view full answer...
I may have a solution for you, but the Thule Hull-a-Port Aero # TH849000 can only be installed on bars with T-slots, which are only found on aftermarket crossbars. Since you have factory crossbars I recommend considering the Yakima JayLow Kayak Carrier w/ Tie-Downs - J-Style or Post Style - Folding - 1 or 2 Kayaks # Y04073, which will clamp to the factory crossbars on your 2020 Subaru Ascent and gives you a J-Style carrier for your boat. The JayLow also folds down similar to the Hull-a-Port... view full answer...
To install the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR in your 2022 Subaru Ascent you will also need the Tekonsha Plug-In Wiring Adapter # 3062-P. This adapter plugs into the connector located beneath your vehicle's dashboard and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 4-pin connector that mates with the adaptor. The other end will then plug into the Tow-Pro Elite. Providing with a simple installation. To help... view full answer...
When putting a trailer hitch on your 2019 Subaru Ascent The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2 inch # e55ZR it will bolt right up to your frame. From what I found in the instructions the hitch will be placed right over the bumper studs, and that's when you attach the factory nuts. It has a gross towing weight of up to 5,000 pounds and has a tongue weight up to 750 pounds. So the hitch is ok for towing 4,000 pounds, but make sure to check your... view full answer...
We can get you set up! Since there is no trailer wiring currently on your 2024 Subaru Ascent, there are two wiring kits you will need. The first is the Curt T-Connector # C56040. The second is the Universal Installation Kit # ETBC7. These two kits combined will have everything you need to wire the vehicle with both of the standard trailer connectors 4-flat and a 7way. It will also include all of the necessary wires for the brake controller.
For the controller we have part # RED44FR. This... view full answer...
To install the Redarc Tow Pro Elite part # RED44FR that you referenced in your 2022 Subaru Ascent all you need is the correct install harness part # 3062-P and you'd be set. There is no need for any additional diodes. view full answer...
The best hitch receiver for hauling a bike with your 2022 Subaru Ascent is going to be the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item # C25VR. This hitch receiver mounts behind your rear bumper bar instead of below your vehicle on the frame. This hitch is concealable behind a removable panel. I have attached an installation video as well as a diagram showing the dimensions of the hitch once installed. view full answer...
Yes, I would recommend installing a brake controller on your 2021 Subaru Ascent since your Aliner Ranger 12 has electric brakes. Most states require you to have a brake controller when towing trailers that have included brakes. The electric brakes on your trailer will not work without first installing a brake controller.
I would recommend The Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR. This proportional controller will automatically adjust your trailer's braking based on... view full answer...
Yes, The Thule Hull-A-Port Aero Kayak Carrier w/ Tie-Downs # TH849000 will fit on your 2021 Subaru Ascent OEM cross bars if you have T slotted top channels. If you do not you would need The Thule Compass Kayak and SUP Carrier w/ Tie-Downs # TH890000.
The carrier # TH849000 has a tool-free installation. The carrier has thick rubber saddles and padded arms that will help protect your hull from scratches and scuffs.
This carrier will carry 1 kayak up to 75 pounds. The carrier has integrated... view full answer...
Kuat does make a 2-inch (only) version of the Transfer V2. The part number of the Kuat Transfer V2 Bike Rack for 2 Bikes - 2" Hitches is # KU84FR.
As far as the clearance between the bumper and the installed hitch on your vehicle, the Kuat Transfer V2 bike rack allows for you to fully access the hatch on most vehicles (with bikes mounted). I looked up pictures of a hitch installed on the 2020 Subaru Ascent, and the hitch receiver sits pretty even with the bumper. However, if you have... view full answer...
To connect the Redarc Tow-Pro Liberty Brake Controller # RED24FR to the factory port on your 2019 Subaru Ascent with the factory tow package you will need a Tekonsha Plug-In Wiring Adapter # 3062-P and Redarc Tow-Pro Wiring Adapter for Tekonsha Brake Controller Harness # 331-TPH-017. Since Redarc does not make a harness for every vehicle they make the adapter for using with the more used Tekonsha pigtails. view full answer...
Yes, we do have a wiring harness that has both a 7-way and a 4-way for your 2020 Subaru Ascent. However, you will need a 4-way connector on your car before this will work though. I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118790. This harness plugs in to existing wiring to provide a 4-flat connector.
The 7-Way and 4-Way all in one connector you referenced is the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and... view full answer...
The Tilting Base for Saris SuperClamp Hitch Racks item # SAR56VR does not come with a locking screw and nut. You will need to purchase the replacement Hitch Tite Anti-Rattle Hitch Pin for Saris Bike Racks item # SA3021. If you would like an anti rattle hitch pin that locks I recommend the Hitch Tite Anti-Rattle Hitch Lock for Saris Bike Racks with 1-1/4" and 2" Shanks item # SA3022. This is compatible with the tilting base SuperClamp. view full answer...
Go To Results