Expert Answers about Nissan Altima

• Derale Transmission Cooler Installation in 2008 Nissan Altima
• To install Derale transmission cooler # D13503 in your 2008 Nissan Altima with 2.5L inline 4-cylinder engine you will need to identify the send and return lines to and from the factory cooler that is inside the radiator. The Derale transmission cooler will install in the return line, which is the cooler of the two lines, the one that leads back to the transmission from the OEM cooler. To find this line, start the COLD engine, shift the transmission into drive for 15-seconds and shut it...
  view full answer...


• Installation Instructions for Draw-Tite Trailer Hitch 24796 and a 2015 Nissan Altima
• There is a bulkhead underneath the 2015 Nissan Altima that will serve as a guide to line the hitch, # 24796, up properly. Once the hitch is in place you will use it as a template to drill the holes needed for installation. I have included a link to the installation instructions and a video showing an example installation for you. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer...
  view full answer...


• Is Drilling Required for Installation of Coil-Rite Air Helper Springs on a 2009 Nissan Altima
• The installation instructions for the Coil-Rite Air Helper Springs, # F4105, indicate that the air line should be routed down, see instructions link, so I went out to our parking lot where there is a 2010 Nissan Altima and checked the lower coil spring seat and found that there is a large hole in the bottom of the spring seat that the air line can be routed through. I attached a photo showing my finger sticking up through the hole in the bottom of the coil seat for you.
  view full answer...


• How To Install Curt T-Connector Vehicle Wiring Harness, # 56022, on 2009 Nissan Altima Coupe
• On your 2009 Nissan Altima Coupe, the black wire has to be run directly to the battery to get power. If you attached to the taillight you would only get power when the taillight is on. The black wire is run directly to the battery to protect the vehicles wiring from any damage, if another power source is used the electrical system would be placed at risk. The yellow fuse wire would be connected inline to the black wire to protect the electrical system from any overload. On any vehicle...
  view full answer...


• Is Drilling Required to Install a Trailer Hitch on a 2013 Nissan Altima Sedan
• The Draw-Tite trailer hitch # 24796 is a confirmed fit for your 2013 Nissan Altima Sedan. Drilling is required for installation. I have included a link to the installation instructions as well as a link to a video showing a typical installation for you to view. All of the trailer hitches that will fit your Altima will require drilling. If you plan on doing some towing the correct ball mount to use is # 3594. Fora 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258.
  view full answer...


• Is Drilling Required to Install a Trailer Hitch on a 2011 Nissan Altima
• All of the trailer hitches for your 2011 Nissan Altima require drilling and temporary removal of the muffler for installation. All of them also are rated for 2,000 pounds gross trailer weight and 200 pounds tongue weight so they can handle a trailer up to those capacities. Check the Altima owners manual for its towing capacities and go by the lower rating. Given what is required to install the hitch it may be worth saving yourself the time and effort and having it professionally installed...
  view full answer...


• How Is The Thule WingBar Evo Supposed To Be Spaced For Installation On A 2006 Nissan Altima?
• I spoke to Thule, and they mentioned that the fit kit for the Thule SquareBar Evo Crossbars # TH712300 will need to be installed 38-3/4" apart for the front, and 37-7/8" apart for the rear. Additionally, the crossbar for the front iwll need to be 10" from the top of the windshield and will need to be spaced 28" from each other. I have attached a couple of images taken from the instructions manual for you to check out as well.
  view full answer...


• How to Install Firestone Coil-Rite Air Springs Lift on 2008 Nissan Altima
• If you do not have a hole in the lower spring seat you will want to mark the hole to be drilled with a center punch in the center of the lower spring seat. Drill a 3/8" hole in the center of the lower spring seat. I have included a link to the installation instructions which will walk you through the process. Please note that Firestone Coil-Rite springs, # F4105, are designed more to keep the rear end from sagging when under load. If the vehicle is sagging in the back and it is not under...
  view full answer...


• Can the Air Pressure in the Coil-Rite Air Springs Be Adjusted on a 2006 Nissan Altima 3.5 SE
• Yes, you can adjust the air in the Firestone Coil-Rite Air Helper Springs, # F4105, to decrease the air pressure when you are not towing. These air springs will be the perfect item to assist the rear suspension on your 2006 Nissan Altima when towing and having a fully loaded vehicle. Once the air springs are installed, you can run the air lines to the location of your choice and adjust the air pressure based on the driving situation. I would recommend that you have your rear suspension...
  view full answer...


• Is Drilling Necessary to Install Draw-Tite Class I Receiver # 24796 on 2011 Nissan Altima
• To install the Draw-Tite Class I receiver, part # 24796 on your 2011 Altima Sedan, you will need to drill a hole through the bottom of the trunk pan using a 7/16" bit. I have linked you to an FAQ article that contains several hitch install tips. I also added a video of this hitch being installed on a 2013 Nissan Altima.
  view full answer...


• Can I Tow a Malone MicroSport Trailer with a Nissan Altima
• What that means is that the Malone MicroSport trailer, part # MPG460G, is level when the bottom of the coupler is 18 inches off the ground. To tow the trailer level you need a ball mount with a rise. Park your Nissan Altima on level ground and measure from the ground the inner top of the receiver hitch. When we installed the Draw-Tite hitch on an Altima we measured 10-1/4 inches. You'll likely be close to this but measure your car so you're sure. Then subtract your measurement from...
  view full answer...


• Does Draw Tite Hitch 24796 Fit 2007 Nissan Altima Hybrid
• The Draw Tite hitch # 24796 that you referenced fits all models of the 2007 Nissan Altima including the hybrid models.
  view full answer...


• Does the Muffler have to be Removed to Install a Trailer Hitch on a 2013 Nissan Altima Sedan
• All of the trailer hitches for a 2013 Nissan Altima Sedan do require temporary removal of the muffler in order to complete the installation. The most popular hitch option for the vehicle is Draw-Tite trailer hitch # 24796 that you have referenced. I have included a link to a video showing a typical installation and a link to the installation instructions for you. If you plan on doing some towing first consult the vehicle owners manual for the vehicles capacities. For a ball mount use #...
  view full answer...


• Parts Needed to Install Yakima Roof Rack on 2017 Nissan Altima
• Yakima recently made some changes to their round bar roof racks but you can still install a round bar rack on your 2017 Nissan Altima but you will need new feet and fit kit. For that the # Y00408 if you needed new bars, # Y28TR for feet, # Y03536 for bar adapters, and fit kits # Y06137 and # Y06127 and you'd have everything you'd need.
  view full answer...


• Will Curt Class II Ball Mount Fit into Draw-Tite Class I Trailer Hitch Receiver
• I just went out to our warehouse and installed the Curt Class II Ball Mount # C45015 into the Draw-Tite Trailer Hitch Receiver # 24796 and it fit perfectly. The Curt is 11-5/8 inches from the hitch pin hole to the hitch ball hole so it will work great for you. For a 2 inch hitch ball use # 19258 and for a 1-7/8 inch ball use # 19256. Then for a pin and clip use # F-4.
  view full answer...


• Does Power Wire of Curt T-Connector Need to Connect to Battery if Trailer Uses LED Lights
• Yes, you would indeed. The Curt # C56339 wiring harness won't function unless that power wire is installed to the positive battery terminal. Obtaining the power directly from the battery makes for a more reliable connection. It also serves to help isolate the vehicle's sophisticated and expensive to repair wiring from any short circuits that could occur in the trailer wiring. You can see the installation instructions by clicking the provided link.
  view full answer...


• Do I Need To Remove Exhaust Heat Shields To Install CURT Trailer Hitch # 11352 On 2010 Nissan Altima
• I do have some hitch options available for your 2010 Nissan Altima that do not require the removal of the heat shields, but the CURT trailer hitch # 11352, does require the heat shields to be removed. The Draw-Tite hitch # 24796 will allow you to retain the heat shields on your 2010 Nissan Altima. It is a Class I 1-1/4 model, and is has the same tongue weight and towing capacity of the CURT hitch # 11352 that you selected. To complete your towing setup, you will need the following items: A...
  view full answer...


• Trailer Hitch for 2013 Nissan Altima Sedan that Does Not Require Drilling to Install
• The Curt # C11352 and Draw-Tite # 24796 require drilling in order to install on a 2013 Altima sedan. If you're needing the hitch as an attachment point for a bike rack or other hitch mounted accessory, I'd recommend the Draw-Tite # 24796. If your owner's manual or Nissan says it's okay to tow with your Altima, you might also need the following: A ball mount Trailer wiring harness, part # 118470 2 inch trailer ball, part # 19258 1-7/8 inch trailer ball, part # 19256 Locking hitch pin,...
  view full answer...


• Can the Power Wire for Trailer Wiring Harness 118470 Go Through the Firewall on a 2012 Nissan Altima
• Like the review states, that grommet should be there. Otherwise you will need to continue looking for a place to drill or route the wire underneath the vehicle. We have an informational FAQ I wrote that should help a little. It does not cover any specific vehicles but it does give you options for routing the wire. It is possible that there are other factory entry points through the firewall. The issue is that the wire bundles going through them may be so tightly packed that getting an...
  view full answer...


• Enlarging Frame Holes To Install Draw-Tite Class I Part 24796 on 2011 Altima Sedan
• The video you refer to was placed on that product page in error. It refers to a different part number installed on the sedan. The install would not involve drilling down through the trunk. The hole closest to the front of the vehicle would need to be enlarged enough so that the block washer and carriage bolt can be fished into the frame member. This hole can be enlarged by drilling a small adjacent hole on either side of the existing hole and using a cold chisel to remove the metal in...
  view full answer...