If you are needing to replace the factory coil springs at the front of your 2004 Workhorse P32 chassis then the higher-rated Super Springs SuperCoils # SSC-11 will work perfectly. These heavy-duty springs will maintain your RV's ride height but provide you with more load support to help reduce front-end sag and bottoming out on the road.
They feature a combined capacity of 7,200 pounds which is going to do a great job of stabilizing your ride and reducing a lot of potential wear on the... view full answer...
When it comes to installing a brake controller on your 2002 Workhorse P Series you first need to make sure you have a 7 round electrical harness on the back of your Workhorse. The Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7 includes all the wiring and accessories required for the installation of the trailer brake controller.
After the wiring is installed then The Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles... view full answer...
The 7-way of your 2001 National Dolphin should have the 12 volt accessory circuit active on the 7-way unless it was damaged over the years. This means that with the Curt Echo part # C51180 you'd just need to plug the controller into the 7-way and once synced to your smart phone you'd be set. view full answer...
The SuperSprings 5,200-lb SuperCoils Custom Suspension Coils # SSC-10 would be the correct set for your 2004 Winnebago that's built on the Workhorse P32 chassis but they are only designed to replace the factory coil springs. If your RV uses a factory air bag system I do not recommend replacing them with these springs. This would likely void any warranty on the RV and could lead to issues down the line since it was designed to work with air suspension at the front.
If you are looking for... view full answer...
The Air Lift LoadLifter 5000 Air Helper Springs part # AL57202 which are a fit for the Workhorse P30 Chassis will require you to remove the existing jounce springs. The air springs will also require drilling into the frame but only a few holes so nothing too major. The Air Lift LoadLifter 5000 Air Helper Springs are the best option for the Workhorse P30 Chassis so they are worth the extra troubles for installation. view full answer...
The two MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan # MA00-03851 you bought will have black and white wires hidden above the fan that you'll connect to the 12v wiring of the trailer. The black wire is your power and the white wire is your ground/neutral. To connect it to the trailer's wiring you'll need to use some butt connectors # DW05714 or wire nuts to splice the wiring together. If there isn't 12v wiring in the locations near the vents then you'll need to run some 14 gauge wire... view full answer...
Yes, if you're currently using the Air Lift 1000 Air Helper Springs for Coil Springs # AL81560 you can remove those when you install the SuperCoils Custom Suspension Coils # SSC-11 on the front of your 2000 Workhorse P32 Chassis. view full answer...
As long as your Workhorse is a widetrack then I would recommend the Roadmaster Front Suspension Bar # RM-1109-200 for your 2000 Itasca Sunrise with a P32 Workhorse Chassis. This anti-sway bar is going to minimize sway and the effects of trucks and wind on your Sunrise. It will improve the stability and driveability of your vehicle which will reduce driver fatigue.
We typically recommend installing one stabilization/sway piece at a time to see how the ride improves before adding more... view full answer...
Although there is no manufacturer recommendation for a ladder on your 2001 Hurricane motorhome I recommend going with the Stromberg Carlson RV Exterior Ladder # LA-401 over the 97" Long Surco Universal Exterior RV Ladder # SP501L or the 84-1/2" LongSurco Universal Exterior RV Ladder # SP502L.
The reason being that the Stromberg Carlson option is 99-1/2" long and can be cut to custom-fit your application. As long as you install it to a part of your trailer that is structurally solid you... view full answer...
For your 2004 Workhorse W22 chassis there isn't a specific custom front mounted hitch receiver. Because of that, I recommend using the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide # C13704 if you have the clearance under your frame for that not to disrupt. An adjustable hitch that is bolt on will be easier than a weld on option, but that is also a possibility. view full answer...
The Furrion Chill RV Air Conditioner and Air Distribution Box would work well to replace an existing roof vent as they both will use the same size 14-1/4" x 14-1/4" cutout. That said, it would need to be used with its own included thermostat as is the case for any air conditioner as they are not universal. The part # FR92PR has controls on the unit and the # FR55PV(also 15,000 BTU) has a separate wall controller. view full answer...
The Air Lift Kit part # AL81560 that you referenced is the correct air bag kit for the front springs of your 2000 Workhorse P30 chassis that your Itasca Sunrise is built on. You would need to remove what is there now and install these in place of them.
I wish we had the bushing you need, but at this time we do not have stock sway bar bushings for RVs like yours. view full answer...
The difference would be capacity and you would notice it. However, I checked with Airlift and there are no 1,000 HD bags that will fit your 2004 P32 Workhorse. The only option for air bags other than the Air Lift 1000 item # AL81560 you referenced is to use the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item # AL88219. These are for your rear suspension and have a 5,000 lbs capacity.
I also recommend adding the Air Lift WirelessAIR Compressor item # AL58WQ to your RV. This onboard... view full answer...
The correct steering stabilizer for a 2002 Safari Trek 26 Motorhome on Workhorse P Series Chassis is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets part # RM-RBK3-RSSP30 so long as you don't have a factory steering dampener. view full answer...
The Camco Replacement Propane Extension Hose - Male and Female # CAM59043 should be able to connect to the # CAM59143 without any issues. It is the same brand with the same connectors and the 12' hose has a male and female end so they are compatible. view full answer...
The correct Roadmaster Front Anti-Sway Bar and Bushing Kit for a 2000 Fleetwood Flair 25Y on Workhorse P Series Chassis is part # RM-1109-116. view full answer...
I do not have an option rated that high for any coaches. The closest I can get you is the Curt Adjustable Trailer Hitch Receiver part # C13701.
It is rated for 500 lbs. of Tongue Weight and 5,000 lbs. of Gross Trailer Weight.
You do need to check your Workhorse Owner's manual to see what it is rated for as a maximum as well and not exceed that. view full answer...
Manufacturers do not list the door handle locks used so you would need to remove the door handle lock from the entry door of your 2001 R-Vision Trail-Lite M-241 Motorhome and measure the cutout hole to find the size needed. For example the Bauer Products Motorhome Door Lock - Black # BA64FR requires cutout hole of 5-1/4" wide x 4-1/2" tall and a door thickness of 1-1/4" to 1-1/2" thick to install. view full answer...
In order to add an anti-sway bar to the front of your 1995 Chevrolet P30 chassis, you will want to use the Roadmaster Anti-Sway Bar and Bushing Kit for Motor Homes part # RM-1109-116. The anti-sway bar will help with side to side movement, driver fatigue, and shifting cargo. It is made right here in the U.S.A. and comes with a 1-year warranty. Unfortunately, there is not an anti-sway bar for the rear of your P-30 at this time.
If you are also looking to add a steering stabilizer then I... view full answer...
I do have suspension enhancement options for a 2002 Workhorse P42 Chassis but there are no air bags available unfortunately. Instead, you can use the Timbren Rear Suspension Enhancement System. The correct one will be based off the suspension. The part # TGMRP30MH is for models with bump stop over u-bolt pad and part # TGMRP30 is for models with bump stop on the frame. These options all work well to provide additional support. view full answer...
Go To Results