Since we know your 2018 Minnie Winnebago 2106DS has a Tor-Flex 3,500 lb trailer axle setup the correct lift kit you'd need is the part # K71-707-02. view full answer...
For your 2021 Winnebago Micro Minne 1800BH I recommend the Adco SFS AquaShed Cover for Travel Trailer - Up to 20' Long - Gray # 290-52240 which due to its Heavy-duty, 3-layer fabric protects that protects against rain, snow, and sun.
The side panels constructed of non-abrasive, triple-layer polypropylene that is breathable to prevent mold and mildew from forming, and the top is made of a triple-layer SFS AquaShed fabric that beads water to prevent it from pooling on your trailer, and protects... view full answer...
It is pretty common for the 3 step RV steps to be a couple inches wider than the 2 step options so I would not be shocked if the width of the Lippert steps # LC432696 being 27-1/2 inches is wider than what you have now. As long as you have the width needed for these to fit they would still work.
The brackets probably won't bolt right up so you could use the outriggers # LC301704 for new ones. view full answer...
The Wisight for Pre-Wired RVs part # ASA24YR that you referenced requires the a Voyager only connector that we can't get any type of adapter for so your best option would be the Furrion Vision S part # FOS43TASF which just needs to wire to the running light circuit of the trailer instead so if your RV wasn't pre-wired it would be the easier and better solution. The Furrion kits have the best signal and reception too which is why we recommend them so highly. view full answer...
The Equal-i-zer Weight Distribution System part # EQ37060ET only comes with a 2" hitch ball but we do offer the 2-5/16" hitch ball separately as the 2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems part # EQ91-00-6100. If you don't have the means to install the hitch ball yourself you can simply take the head and hitch ball to a nearby shop and they can torque it down for you. view full answer...
Your axle picture is a little blurry but it looks like I can tell that it's a 3,500 lb Lippert torsion axle so the lift kit you'd need is the part # LC270682 if the axle is orientated like a "square" or part # LC382741 if it's orientated like a "diamond". view full answer...
I would be happy to help!
For your 2021 Winnebago Micro Minnie 2108TB I recommend the Adco Polypropylene Storage Lot RV Cover for Travel Trailer # 290-74840 which is a confirmed fit for your trailer, and will be a perfect choice for your climate.
The Polypropylene is perfect for use in any climate, including the warm weather you get in Arkansas while its heavy duty construction allow the cover to hold up even in the worst conditions. view full answer...
The Adjustable Width Trailer Hitch Receiver for RVs part # 13703 has a 350 lb tongue weight rating so as long as the weight of the bike and rack don't exceed this and the hitch is installed properly then won't have any issues. It attaches to the frame so it's much stronger than the ones that go on the bumper but this does also mean you must drill into the frame to install it. view full answer...
If this is too firm for your comfort is only identified by you, I can advise however that the Denver Mattress Comfort Choice RV Folding Mattress, # DE28ZR holds the mid level rating for firmness. view full answer...
The Lippert # LC270682 Axle Riser Kit you'd specified is indeed the correct kit for your application. The riser kit would provide 3-1/2 inches of lift, and each kit will raise one axle. So, for your tandem axle trailer you'd need to order two of them.
If you click the provided link, you can see a product description video featuring the lift kit. view full answer...
A quick and easy jack upgrade can be done with the etrailer # EJ-3520-BBX Electric Jack with foot plate.
You can further upgrade by selecting the Lippert # LC643589 Smart Jack. Hitch memory automatically returns your trailer to the position at which you unhooked. Up/down buttons allow easy one-touch operation. Check out the attached videos to see the extra features.
Both of these jacks install where you old one is right behind the coupler and will not interfere with your weight distribution... view full answer...
That's going to depend on the entry height and width of the cutout under the door of your 2018 Winnebago Micro Minnie 1808FBS, but based on the pictures I can find I kind of doubt anything more than a single step unit will work.
If you can send me the measurement from the top of the mounting cutout for the steps to the ground, and the width of that cutout I can check for you.
If you cannot fit another step then you'll just need to use a portable single step # SASXLA-09C-G which is adjustable... view full answer...
For a customized RV cover with the Winnebago Flying W logo on it, we have in stock the Winnebago Adco RV Cover, # 290-64843 with actual dimensions of 315" long x 100" wide x 96" tall. This is listed for Winnebago travel trailers 22'1" - 24'. While this may be a little longer than needed if yours is measured at 23' and 6", not including the trailers tongue, it has cinch ropes at front and rear of cover used to remove some slack. This also has straps secured under the vehicle to prevent... view full answer...
I have another option for you, but the Bumper Mounted Tire Carrier - U-Bolt Mount # TR-1 you were looking at only works with wheels that are 15" - 16" in diameter and would not be correct for your 14" wheel.
Instead I recommend going with the Brophy Rigid Mount Spare Tire Carrier # BR56VR which works with wheels up to 17-1/2", and since we had a chance to use it with a 13" wheel we can confirm it will work perfectly with your 14" wheel.
I included a video of the # BR56VR for you to take... view full answer...
I looked up some pictures of your 2021 Winnebago Micro Minnie 1808 FBS and it has an Alumi-Tread pull out step so for a three step version you'd need the part # LC432696 and you'd be set. view full answer...
The best storage cover for your 2021 Micro Minnie 2100BH is the Adco SFS AquaShed part # 290-52240 which provides the best protection and has the easiest install. view full answer...
I do have options for you but you will either be drilling into the roof to attach the roof rack or drilling into the roof to attach the solar panels. There are no drill free options for the roof but if the panels are installed properly there will be no leaks to worry about. It's not like you're drilling all the way through anyway. The only way around this is with portable solar panels which you would setup outside the trailer each time. I am not sure how much solar you need but for a portable... view full answer...
The cover I recommend for your 2022 Winnebago Micro Minnie 2108TB is the Adco Olefin HD All-Climate + Wind RV Cover # AD97ZR which fits trailer boxes up to 20' long. It looks like your trailer measures about 22-1/2' including the tongue and since the storage covers only fit over the body of the trailer this will be perfect for your application as it's designed for all weather conditions.
Attached is a review video for you to check out. view full answer...
The Winnebago Micro Minnie 2108 DS measures 22'5" long so in order to find the correct storage cover we just need to subtract 3' for the tongue and round up. Therefore, we're looking at a cover for a 20' trailer and for this I recommend the Adco SFS AquaShed RV Cover for Travel Trailers up to 20' Long part # 290-52240 if you live in the north or the Adco Olefin HD RV Cover for Travel Trailers part # AD97ZR if you live in the north or south. These are both great options, the only difference... view full answer...
The Adco # AD97ZR would be your best option for a storage cover for your Winnebago Micro Minnie 2100BH. This will provide you with the best protection for the high winds and rain you'll see in Southwest Washington as well as provides the easiest install as well. view full answer...
Go To Results