The Air Lift Ride Control Air Helper Springs # AL59564 that you referenced are designed for load support when you are carrying heavy cargo in the bed of your 2015 Toyota Tacoma so that you can level it.
It's not really designed to be used as a lift kit, but if you were to inflate the bags to a high enough pressure you should see it raise the rear of your truck a couple inches. The ride quality will be pretty harsh at this point though. A lift kit for the rear of your truck might be a better... view full answer...
If your trailer is rated at 5,200 lbs most likely you have axles that are rated less than that individually. Typically on the VIN plate of the trailer the axle capacities will be listed. Common axle capacities are 5,200 lb, 3,500 lb, and 2,200 lb so most likely you probably have 3,500. But you can also measure the diameter of them too to determine this.
- 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter
- 3,500-lb Axles: 2-3/8 inch diameter
- 5,200-lb - 7,200-lb Axles: 3 inch... view full answer...
No, they will not. The SumoSprings Solo Custom Helper Springs item # SS57PV replace the bump stops on your 2014 Toyota Tacoma which will not affect the ride height of your truck. view full answer...
I went out into our warehouse and measured a Square Direct Weld Jack w/ Footplate # TJD-5000 and found that the dimensions are 7-1/2 inches long by 3-3/4 inches wide.
I included a video review of this jack. view full answer...
The distance from the top of the mounting surface of the Rear Hanger for 2" Wide Slipper Springs # 721585 down to bracket that the spring would rest on is 2-3/8 inches. view full answer...
We generally recommend that you have 4 inches between the tops of the tires and the underside of the fender to allow for travel of the suspension. It could require more or less space but it is more likely to require less than more. Four inches is pretty far and the deflection on # ASR2000S02 is 2-5/8 inches so it should be just about perfect depending on the tire size. view full answer...
The Westin Sportsman Grille Guard # 40-1605 for your 2009 Toyota Tacoma weighs about 90 pounds by itself. The Westin MAX Winch Mounting Tray # 46-21605 weighs about 60 pounds.
This means both items together will add a total weight of around 150 pounds to your Tacoma.
I have attached the written installation manuals for these products below that you can also take a look at. view full answer...
The recommended minimum distance between the top of the truck bed side rail and the underside of a fifth wheel trailer is 6 inches. This is usually enough clearance to allow for roll and pitch when driving on uneven roads, dips or hills, but there may be some towing setups that require more clearance.
If you think your trailer may hit your truck bed with it's current setup, then I recommend either raising the height of your fifth wheel hitch or lowering the pin box position on the trailer.... view full answer...
Rough cut openings for roof vents have a bit of wiggle room on the dimension. Between 14 inch and 14-1/4 inch would work well with the Fan-Tastic roof vent part # FV802250. view full answer...
If your trailer's maximum fully-loaded weight will be 1200-lbs then you can use one of the 1200-lb-rated Timbren kits shown on the linked page. These are available with or without a choice of idler hubs. One kit include brake flanges in case you want to add brakes in the future, kit # ASR1200S04.
The kits rated for 2000-lbs could still be used but you'd find the ride to be a bit rougher since they'd be operated well below their maximum capacity. Their extra stiffness would make the trailer... view full answer...
The Yakima OverHaul HD Adjustable Truck Bed Ladder Rack # Y01151-5855 weight capacity at any height will be 500lbs on-road, 300lbs off-road, and 800lbs static.
Note: The maximum weight ratings will be reduced by 40% when using crossbar spreads less than 36". view full answer...
The Yakima OverHaul HD Adjustable Truck Bed Ladder Rack item # Y01151-58 does include a lock set to secure the ladder rack to the bed of your 2018 Toyota Tacoma. They are at the base of two of the uprights. One will go in the front set and one for the rear.
I have attached a couple of pictures below so you can see how the bases are secured. I have also linked the instructions so you can see how this system sets up.
The SKS cores can also be swapped out to make all your Yakima products... view full answer...
For mounting a 15" wheel on the CE Smith Trailer Idler Hub Assembly # CE13515 you will want to torque the wheel nuts to either 90-120ft-lbs on a steel wheel or 90-100ft-lbs on an aluminum wheel. I have included our a wheel torque chart below as well. view full answer...
To carry lumber and tools with your 2023 Toyota Tacoma you are going to want the Thule TracRac TracONE Truck Bed Ladder Rack item # TH27000XTB-XK4B. This fits both the 5 foot beds and 6 foot beds with the deck rail system.
The Thule ladder rack system has a no drill installation and a 800 lbs capacity. The system attaches to the side of your bed rails using screw down clamps like you would use to attach a camper shell. Each upright is held on by two.
The slotted crossbars accept a wide... view full answer...
The 80 lb weight capacity of the Jack-It 2 Bike Rack for A-Frame Trailers # LC429756 is the total weight capacity for the rack.
I have added a link to a video review of the Jack-It for you to check out as well. view full answer...
The minimum height for the Trailer Valet XL # TVXL2 is 19-1/4 inches. The maximum height is 20-1/4 inches.
Please keep in mind that when leaving the Trailer Valet hooked up to your trailer on a slope that you will want to use chocks, like part # 3605, to help secure your trailer.
I have included some demonstration videos for you as well. view full answer...
The hitch bolt included in the Yakima Replacement Mounting Hardware for SwingDaddy Hitch Mounted Carrier # Y8890185 measures exactly 4.28 inches long with a 1/2 inch diameter and 13 pitch.
If you only need the bolt and clip you can use part # Y8890176. view full answer...
I spoke to my contact at Rhino Rack and he informed me that the length of the roller on the Rhino Rack Ladder Roller # RR1500 that you referenced is 56-1/4 inches.
Check out the picture I attached to see this measurement. view full answer...
The height can be adjusted on Rack'em trailer ladder rack # RA-28.
It the highest position it measured 27 inches tall overall and 22-1/2 to the top of the crossbar.
From the bottom of the rack to the very top in the shortest position it is 22-1/8 inches tall. From the bottom to the top of the crossbar it is 17-5/8 inches tall. view full answer...