I spoke with my contact at MagnaFlow and he informed me that all of their cat-back systems are designed to be under the 95 decibel rating that is mandated. He could not give me an exact figure, but you should be fine.
He did say also that all of their systems are tested on stock vehicles where the only thing that is changed is the installation of the cat-back system. So if you install headers, intake or an offroad y-pipe you could exceed this. view full answer...
63 inch long tracks are included with the Rhino Rack Roof Rack part # Y02-480B that you referenced. The crossbars are 54 inches long. view full answer...
I went out and measured the mounting plates, part # 337MFBH2375A, for you. At its longest point it measures 23-3/4 inches and the shorter distance is 19-3/4 inches. It's 3 inches tall 1 inch deep from the bend.
The first mounting hole is 1-1/2 inches from either end and the holes are all inches from each other, center on center.
The metal itself is 0.135 inches thick. view full answer...
Curt trailer hitch # 13199 for the 2015 Nissan Titan has a maximum gross trailer weight capacity of 10,000 pounds when used with weight distribution. The other hitch option for the truck, Draw-Tite hitch # 41551, has the same rating. On the 2015 Nissan Titan the maximum towing capacity for any of the various configurations of the truck that has the factory tow package is 9,500 pounds. Consult the vehicle owner's manual for the capacity of your specific model. view full answer...
No, you won't have to modify the Util-Track system to install the Lomax Hard Tonneau Cover item # LOM66QR. The rails for the tonneau cover mount about the track system on your 2017 Nissan Titan. I have linked the instructions below so you can see the process. view full answer...
The 2016 Keystone Outback Super-Lite Series M-325 BH travel trailer has a gross vehicle weight rating (GVWR) of 10,500-lbs. This figure is the sum of its dry weight (8325-lbs) and its carrying capacity (2175-lbs) and is the most this trailer can safely weigh when loaded.
I checked the online edition of the owner's manual for your 2009 Nissan Titan and the very most the best-equipped version of this truck can tow is 9500-lbs (this is for the 2WD King Cab XE and SE versions with short wheelbase... view full answer...
When installing a universal fifth wheel rail kit like the Reese part # RP30035-405 the rear rail edge will be 26-1/2 inches from the rear edge of the rear of the truck bed of your 2005 Nissan Titan. view full answer...
Measure from the awning rail on the side of your RV down to see how much clearance you have for an awning rail. The part # LC434730 requires 69 inches of clearance from the rail down. If you have the needed clearance this would be all you'd need. view full answer...
I spoke with my contact at Flint Hill Goods about the temperature rating. He said that there is no problem with the hitch cover # FHG72VR performing in cold temperatures as low as those you experience in Fairbanks.
The Flint Hill Goods Square LED Brake Light Hitch Cover for 2" Hitches # FHG72VR will fit 2 inch trailer hitch receivers. The light requires a standard 4-way flat trailer connector for power and signal. This lighted hitch cover should work well for your 2013 Nissan Titan Pro... view full answer...
The distance between the holes on the Tow Ready Adjustable Tow Bar, # 63180, mounting bracket measures 4 inches from center to center.
The attached picture will show you additional measurement information for you to review. view full answer...
While two Thule Hullavators will fit the dimensions of your 68-inch wide crossbars and are compatible with the t-channels on the Yakima HD bars on the Yakima Overhaul HD # Y01151-5868, one of the things to note is that the Hullavator requires 4-8 inches of crossbar space after the leg supports of the OverHaul HD in order to function properly. Since every ladder rack fits every truck model differently, I recommend measuring your crossbars outisde of your truck's bed rails to see if there... view full answer...
The hub bore of Trailer Hub and Drum Assembly # AKHD-655-35-K is 1.980-inches and this allows a good fit with a grease cap like # F001518 which has a flange diameter of 1.988-inches. view full answer...
The height of the SumoSrpings Solo Custom Helper Springs # SS95GR is 5-1/2 inches without the top bolt and 6-1/2 inches with the top bolt. I went ahead and attached a diagram of these dimensions to give you perspective.
If you need the confirmation for a fit with your vehicle, I would be happy to assist you if you provide your year/make/model. view full answer...
The cable that comes with the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer - Dual Spring - 150-lb Capacity # 362SA8207 is 150" and can be replaced with part # CAB1-8CB150. I confirmed this with my contact at TRC.
If you needed to get a longer cable set then we have the 174" Long Cables as part # M339FR. view full answer...
The uprights of the Adarac Aluminum M-Series Custom Truck Bed Ladder Rack - Aluminum - 500lbs # A67VW are 12" tall and the crossbars are 1-1/2" tall. view full answer...
The Dexter Shackle Bolt for Double Eye Springs # 007-126-01 measures 2-1/4" from bolt head to threaded portion. This bolt is 2-7/8" long and has a thread size of 7/16"-20. You can use Replacement 7/16"-20 Flange Nut # LC122103 with this bolt. I have attached a demonstration video for this bolt. view full answer...
The distance between the mounting holes of the Reese Shank part # RP54970 is 1-1/4 inches and the diameter of the holes is 3/4 of an inch. view full answer...
There are two dimensions that I can provide for the Malone HighRise # MPG323. The main black part that will attach to the wall is 10-3/16" long; when you put the arm into that piece, which will hold the boat, the length will be 13-1/4" total hanging down. view full answer...