The Thule hardware # TH04997 kit is a confirmed fit for your Thule Mountaineer roof cargo box.
I have linked the review video of this replacement hardware for your convenience. view full answer...
Yes, the Replacement LED Light for Stromberg Carlson Electric A-Frame Tongue Jack # 2500-06 will replace the old incandescent lights that you currently have on your Stromberg Carlson Electric Trailer Jack # JET-3755. view full answer...
We do not have just the single legs by themselves for landing gear # RVLG-8000 but you could use the leg from a different brand such as # LG-179013 but the cost of this single leg is more than a whole new # RVLG-8000 system. Based on this I recommend replacing the whole system. It costs less and you get all new parts!. view full answer...
I am not sure what 2005 Lincoln you have, but if it's a 2005 Lincoln LS like what the Curt hitch part # C12253 you referenced is designed to fit the answer would be "no it could not carry a 500 lb scooter on a hitch mounted carrier." The only solution with this vehicle would be with a small trailer towed with this hitch installed.
For trailer wiring you'd then need the part # C55373 which I recommend as it installs easily and is very reliable, and then for a ball mount # 36071 with hitch... view full answer...
I might have an option for you but we don't have any replacement parts for the Fit Kit for Thule Evo Flush Rail and Edge Flush Rail Roof Rack Feet part # TH66RV. If this is what you need you'd have to reach out to Thule directly. That said, what I think you're looking for is replacement end caps for the feet which mount to this fit kit and if that's the case we do have an option for you, we'd just need to know what feet you have. If you have the Evo Flush Rail Feet for Thule Crossbars part... view full answer...
From this and the additional information you provided (such as the casting number from your brake drums), I've found that your Coachmen Clipper uses a 7 x 1-1/4 Inch electric brake assembly. If there are wires You would want to use # 23-47 for the left side and # 23-48 for the right side. Mounting hardware is included with the assemblies
You might also consider replacing your brake drums as well. Take a good look at the armature surface (the surface the brake magnet rides against) and... view full answer...
I can help you find the right assemblies, but I do not know exactly which ones you have on your 2008 Palomino 25RS.
To pick out the correct brake assemblies for your trailer you need to know a few things.
You will want to measure the inner diameter of your hub/drums and the depth of the drums to determine what brake assembly dimensions you need. For example the part # 23-468-469 is a 10 inch by 2-1/4 inch thick brake assembly set. I attached an install video for this kit for you to check... view full answer...
I was able to find the parts list on your MaxxAir MaxxFan 8900K and the correct replacement lift motor is going to be the Replacement Lift Motor for Maxx Fan Plus Roof Vent # MA10-20270; so you were on the correct part. view full answer...
We do indeed offer replacement step pads. You'll need part # 21-0001 which does include the necessary barrel clips. The replacement step pads are sold individually. view full answer...
Your measurement of 1-1/16 equals to 1.0625 inches and most likely the bearing is # L44649 and the inner bearing is # L68149.
With that said, I think bearing kit # BK2-100 will work, but I strongly recommend looking at your bearings, races and seal for part numbers or taking a few measurements.
The best way to determine the correct parts for your 3,500 pound boat axle trailer, is to remove the hub from the trailer and either get part numbers from the inner and outer bearings and races,... view full answer...
I took a look at your 2006 Starcraft Toy Hauler and it appears that you have the Bargman LED Clearance or Side Marker Light 47-59-002 as your taillights, which then you'd need the Replacement Amber Lens for Optronics MC32 or MCL32 Series Clearance or Side Marker Trailer Lights # A32AB for a replacement lens.
This lens measures 4" long x 2" tall x 1/2" deep, so you'll want to double check with your current lens to be sure. If it turns out you need a different size or you have a different... view full answer...