Recommended Trailer Brake Assemblies for 2003 Coachmen clipper
Question:
Hello, I am trying to find the proper brake assembly for my 2003 coachmen clipper model 520 Serial #1tc1c520535001274 with combined axle rating 2090 lbs . Can you recommend some brake assemblies ... Thanks
asked by: Shawn
Expert Reply:
From this and the additional information you provided (such as the casting number from your brake drums), I've found that your Coachmen Clipper uses a 7 x 1-1/4 Inch electric brake assembly. If there are wires You would want to use # 23-47 for the left side and # 23-48 for the right side. Mounting hardware is included with the assemblies
You might also consider replacing your brake drums as well. Take a good look at the armature surface (the surface the brake magnet rides against) and if you see any grooves, pitting or discoloration, you should also replace the drums with part # 8-173-16UC3-EZ. The drums include bearings, races, seals, lug nuts and an EZ-Lube grease cap.
Products Referenced in This Question
Dexter Electric Trailer Brake Assembly - 7" - Left Hand - - 2,000-lbs to 2,200-lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 2000 lbs
- 2200 lbs
- Brake Assembly
- Manual Adjust
- 7 x 1-1/4 Inch Drum
- Dexter
more information >
Dexter Electric Trailer Brake Assembly - 7" - Right Hand - 2,000-lbs to 2,200-lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 2000 lbs
- 2200 lbs
- Brake Assembly
- Manual Adjust
- 7 x 1-1/4 Inch Drum
- Dexter
more information >
Dexter Trailer Hub and Drum Assembly for 2,200-lb E-Z Lube Axles - 7" Diameter - 4 on 4
- Trailer Hubs and Drums
- Hub with Integrated Drum
- EZ Lube
- L44649
- L44649
- For 2200 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly - 10" - Right Hand - 3,750 lbs
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Free Backing
- 10 x 2-1/4 Inch Drum
- Dexter
more information >
Continue Researching
- Q&A: Bearing Kit for 3,500 lb Trailer Hub
- Q&A: Greasing EZ Lube Spindles When Grease Comes Out Cotter Pin Hole
- Q&A: How Tight Does the Castle Nut on a Trailer Spindle Need To Be
- Q&A: Replacement Hydraulic Brakes and Hub/Drum Assembly for 3,500 lb Boat Trailer Axle
- Q&A: Parts Needed To Replace Hydraulic Braking System On Boat Trailer
- Q&A: Correct Replacement for AL-KO 7230 Hub/Drum and Brakes
- Q&A: Should I Paint U-Bolts to Protect Finish
- Article: How to Measure the Bolt Pattern of a Trailer Wheel
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Bleed Your Trailer Surge Brakes
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Trailer Jacks
- Article: 7 Common Questions Everyone Has About Trailer Tires