No, you can't. Those hooks are only for recovery or pulling something they're not rated to be flat towed with. You are actually going to have to remove them to install a base plate kit on your 2023 Ford Bronco.
Since you have a Blue Ox Alpha tow bar you'll want the Blue Ox Base Plate Kit item # BLU23XR. This base plate kit is confirmed to fit the Bronco's with the Ford modular front bumper.
Here are some other parts you will need to flat tow your 2023 Ford Bronco:
Wiring Harness -... view full answer...
To add a roof rack to your 4-door 2023 Ford Bronco, I recommend the roof rack by Yakima and it includes the following parts:
Yakima JetStream Crossbars - Aluminum - Black - 60" Long - Qty 2 item # Y00426
TimberLine Towers for Yakima Crossbars - Raised, Factory Side Rails - Qty 4 item # Y33TR
This aero bar roof rack system has a 165 lbs capacity. I recommend adding the Yakima Same Key System item # Y07204 to prevent theft. Since you're a fan of Yakima's products you can also buy larger... view full answer...
Since your Rockwood Trailer comes prewired you will want the Furrion Vision S Wireless RV Backup Camera System w/ 3 Cameras item # FCE48TASL-05. This system includes a 5" monitor, rear camera, and two side marker cameras.
If you are just wanting the rear camera and monitor you'll need the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision item # FOS05TASF. view full answer...
The recommendation would not change because the base plates install in the same location on both the modular and capable bumpers. Same with a potential lift. Something like that would be addressed down the road with a high low adapter if necessary.
To flat tow your 2023 Ford Bronco Badlands with a capable bumper you will need the follow parts:
Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item # RM-520 and item # RM-643
Base Plate Kit - Roadmaster Direct-Connect Base Plate... view full answer...
I can help you determine how far down the step of the Aries ActionTrac Motorized Running Boards with Custom Installation Kit # AA58RD would hang down but I don't have the exact figure you are looking for that I can give you. If you measure right at 12 inches from the bottom of the lower door panel you'll know where the top of the step would be. view full answer...
The center of the hitch pin hole for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR is 6" further out than the center of the hitch pin hole for the Curt Trailer Hitch Receiver # C76WR. Since the hitch pin hole determines where your accessory will be sitting this is the dimension you want to take note of as opposed to the end of the receiver tube.
I went and measured the Curt hitch and from the outermost mounting plate that installs on your 2022 Ford Bronco to the center of the... view full answer...
The length of the power cord on the Demco Wireless LED Light Bar for Towed Vehicles part # DM36MV is 11-1/2'. This should be plenty to reach from the nearest outlet to the rear windshield. view full answer...
The Roadmaster Sterling Tow Bar item # RM-576 is compatible with both direct connect and crossbar style base plates so depending on which model you have you may need to remove the crossbar. The base plates for the 2022 Ford Bronco install where the D-rings are mounted. They have to be removed as they are not rated to be flat towed with.
To flat tow your 2022 Ford Bronco you will need the following parts:
Safety Chains - Roadmaster item # RM-643
Base Plate Kit - Roadmaster Direct-Connect... view full answer...
Since your tongue weight is 530 lbs, I recommend the Equal-i-zer Weight Distribution w/ 4-Point Sway Control item # EQ37061ET. It has a tongue weight range of 200 lbs - 600 lbs so you'll be covered if you're above or below that 530 lbs number. This system has built in sway control that will keep your trailer in line with your Bronco if you make a sudden move or get passed by a semi. This system does not include a shank but it does have a 2" hitch ball.
For a long enough shank to clear... view full answer...
The best base plate for your 2023 Ford Bronco is the Roadmaster Direct-Connect Base Plate Kit item # RM92ZR. You will need to use the Demco Tow Bar Adapter Kit item # DM9523032 to connect it to your Demco Dominator item # DM9511008. There is a Demco base plate item # DM76GV but it only works with the plastic bumpers. The Roadmaster is compatible with your steel one.
Some other parts you will need to flat tow your 2023 Bronco are listed below:
Tow Bar Wiring Kit - Roadmaster Diode 7-Wire... view full answer...
The Fulton Economy Spare Tire Carrier # FETCLB0201 will measure 9-5/8" long and 4-5/8" wide going outside to outside. This will also fit frames up to 3" wide. I included a full diagram with all measurements for you to take a look at as well. view full answer...
To flat tow your 2023 Ford Bronco with a standard bumper you will need the following parts:
Tow Bar and Safety Chains - etrailer SD Non-Binding Tow Bar for Direct-Connect Base Plates item # e74ZR
Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM79RR
Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267 for incandescent bulbs or item # RM38FR if you have LEDs.
Charge Line Kit - Roadmaster Battery Charge Line Kit item... view full answer...
The best option to add a hitch to your 2023 Ford Bronco is the Curt Trailer Hitch item # C76WR. This hitch is custom fit and bolts to your Bronco with included hardware. This is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity and 350 lbs maximum tongue weight.
I have attached a couple of pictures below along with an installation video so you can see what this hitch looks like when installed.
If you are planning on towing you will also need a wiring harness item... view full answer...
The best hitch for a bike rack on your 2024 Ford Bronco is the Draw-Tite item # DT37GR. This hitch is custom fit and bolts to your Bronco's bumper with included hardware.
The Draw-Tite item # DT37GR was specifically designed with a longer receiver to clear your spare tire. The hitch pin hole extends 7" past the outside edge of your Bronco's bumper. It extends 6" farther than the Curt item # C76WR you were looking at. This hitch also has the highest capacity available amongst Bronco hitches.... view full answer...
I recommend the Roadmaster High-Low Adapter for Tow Bars item # RM-048-4. This high low adapter will provide a 4" drop. To be considered level the tow bar needs to be within 3" of your base plates. view full answer...
To flat tow your 2023 Ford Bronco with a plastic front bumper you will need the following parts:
Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item # RM-520 and item # RM-643
Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM79RR
Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267. This diode kit will splice into your tail light wiring to display the signals from your motorhome through the tail lights of... view full answer...
I have a solution for you but Demco does not have a baseplate kit for a 2023 Ford Bronco. However, if you are using a Demco tow bar there is an adapter available that will work with the item # RM79RR baseplate you were looking at. It is the Demco Tow Bar Adapter Kit for Roadmaster Direct-Connect Base Plates item # DM9523032.
I have linked an installation video below so you can see this adapter being used.
The Roadmaster Direct-Connect Base Plate Kit item # RM79RR is confirmed to fit... view full answer...
For hold down pins that are at least 2-1/2 inches long, there are the 3 inch long pins that come with the Shoe Hold Down Spring for 10" Trailer Brake Assemblies # BP06-120.
These pins are not available individually, they do come with the springs, and fit 10" x 2-1/4" Dexter, Bendix, and Demco/Dico electric and hydraulic brakes. view full answer...
Yes, we do! To access our network of reliable installers all over the country you will want to go to the left hand side of the Item # DM86VR product page. Underneath the installation videos is a blue link that says Locate installers near me. You will want to input your zip code to get a list of installers in the Leesburg area. view full answer...
To flat tow your 2023 Ford Bronco with the Ford factory bumper you will need the following parts:
Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item # RM-520 and item # RM-643
Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM92ZR
Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267. This diode kit will splice into your tail light wiring to display the signals from your motorhome through the tail lights of... view full answer...
Go To Results