We have Trailair Flex Air fifth wheel pin box replacements for Lippert 1621 and Lippert 0719 pin boxes.
You will need to know what model pin box you have on your trailer to find the correct replacement. You can typically find that information on a sticker or a tag on the side of the pin box. If not and if it is the original pin box you can contact the dealership and give them the VIN and they should be able to tell you what pin box number was installed on your trailer.
If you find you... view full answer...
You're looking for the Base Rails # TH21781 which fit the Thule TracRac SR # TH43002XT-781 for your 2020 Chevy Silverado 2500HD with the 6-3/4' Bed. view full answer...
We do have those replacement parts for the Air Lift LoadLifter 5000 Ultimate Air Helper Springs # AL88338 on your 2017 Chevy Silverado 2500. The clamp bars and fittings are sold indivuidually so you will need 2 of each from the lift below:
Replacement Clamp Bar - # AL01851
Replacement Elbow Fitting - # AL21848
Replacement Main Hardware Kit - # AL34921 view full answer...
From what I have found, the 749 lbs on your Grand Designs Transcend 297QB is the dry tongue weight. Since you will have propane and other cargo in the trailer that will definitely be over the 750 lb maximum for your current spring bars. Also, any cargo behind the rear axle of your 2022 Chevy Silverado 2500 will be considered tongue weight as well.
Since you will be over 750 lbs that means that the spring bars for your current setup won't be effective. You will want to add the Replacement... view full answer...
Yes, the motor for the Lippert Components PSX2 Electric RV Stabilizer can be replaced without obtaining an entire new system. The Replacement Motor and Gear Box Assembly for Lippert Components PSX2 Electric RV Stabilizers part # LC759091 is what you will need for this. The motor and gear box assembly come as one unit and must be replaced together.
I suggest keeping one spare motor/gear box on hand so you never have any down time but if worse comes to worse you can still operate the jack... view full answer...
The Extang # EX1032 replacement hinge that you referenced is made for Extang Trifecta and Extang eMAX folding tonneau covers as a hinge replacement. I reached out to my contact at Extang and found out that they also make the Gator covers and that this hinge will work with Gator brand covers! view full answer...
For a WFCO-8955 power center you would need the Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel # PD4655V for a direct swap of your current converter. view full answer...
You're in luck! The 2013 and 2015 Chevy Silverado 2500 use the same frame brackets. Assuming you already have the bed rails and the frame brackets, but only need the hardware, here's what you'd need:
To install the brackets to the truck frame, you'll need the # RP50066F hardware kit. To attach the bed rails to the frame brackets, you'll need the # RP58430 hardware kit.
I've linked you to the installation instructions for the install kit (in case you don't have them any more) as well as... view full answer...
Yes you can do exactly what you mentioned doing. You can take the head from your current Companion hitch and install it on the B and W Slider Base for 2020 GM rail kits part # BWRVB3775 and you'd have a hitch that fits your truck. Basically you'd have the # BWRVK3775 at that point. view full answer...
For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part # LC62ED and the correct replacement drive arm (one with the motor) is the part # LC22ED. view full answer...
For your 2015 Chevrolet Silverado 2500 with the 6-1/2' short bed and Truxedo Low Pro Tonneau cover there are 2 options for a replacement rear header. The Rear Header # TX5727-RearHeader is for the Cover # TX572701 that fits with a Sport Bar installed. Otherwise the Rear Header # TX5720-RearHeader is for the Cover # TX572001 without a Sport Bar. view full answer...
In order to find the correct replacement slipper spring you will need the length, width, and the capacity. The leaf count does not indicate capacity and is not important when determining a replacement. This information would also make a difference in the mounting hardware.
For example, the 4-Leaf Slipper Spring w/ Open Eye End # e24SR is 27" long, 1-3/4" wide, and designed for 4,300 lb axles. Assuming a single axle, you could use the # APS3SE and # APUBR-1 (this is for a 2-3/8" diameter... view full answer...
Assuming you have the 2024 Silverado 2500 long bed you can use the Curt OEM 5th Wheel Hitch Legs for Chevy/GMC Towing Prep Package # CU53FR. This will allow you to use the A16 Head # C16520 with the prep package in your truck. If you have the short bed and your A16 is one of the slider models you will have to use the Adapter Rails # C88KR. view full answer...
The landing gear legs on your 2010 Jayco Eagle could be made by a few different companies but I would not know exactly which one that is. That said, brand is not really needed for choosing the correct replacement but rather length. If the outer tube measures 33-1/2" long then I can confirm the Replacement Lead Leg part # LG-177202 is what you need. view full answer...
The Replacement Motor for Stromberg Carlson Electric Landing Gear Set part # LG-196308 should work in place of your Atwood 70079 Landing Gear Motor. I cannot confirm this as Atwood Landing Gear parts have been discontinued for some time so there is no way to test this but after looking both over I do believe they will work in place of one another. view full answer...
You can change out your Lippert Turning Point pin box for the Trailair Air Ride 5th Wheel Pin Box - Lippert 1621 & 1621HD - 21,000 lbs # LC158778 as long as the mounting points are the same and you are within the capacity of your pin box.
I've attached an article to assist with the mounting points based on measurements to assist. If you want to keep the rotating pin box and add the air ride there are a couple Reese Sidewinder options that have both. I've linked the page to those options... view full answer...
From what I could find, the Extang Tuff Tonneau for your 2015 Chevrolet Silverado 2500 with regular (6-1/2") bed is the 14450 cover. The correct replacement tarp for that cover is the Replacement Tarp for Extang Tuff Tonno Roll-up Soft Tonneau Cover # EX13450.
I do recommend verifying the 14450 is the cover that you have. You can do this by locating the part number. The part number is typically stamped along the underside of the cover, typically located at the driver side cab corner. view full answer...
Your 2005 Keystone Montana Mountaineer uses a unique landing gear system and we do have the exact replacement legs available that you will need. For the Lead Leg you will use the Lippert # LC178653 and for the Follow Leg you will use the Lippert part # LC178652. These are OEM replacement units and they will work perfectly on your trailer. view full answer...