To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming.
Features:
Inno Aero Aluminum Load Bars - 48" Long - Black - Qty 2:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2013 Volkswagen Jetta we're doing a test fit of the Inno Aeroblade Crossbars. The part number for our crossbars today is I9XB100-2, for our foot pack we're using INXS200, and for our fit kit, we're using INK590. We already have our front bar on, we're going to show you we put the back bar together. We've just got one foot pack left and then we'll load it up onto our vehicle. It comes with everything you see here. The only thing you'll really need to provide is a flat tape, or even a tape measure will work for that as well. First thing we're going to do is put our foot pack together.
I'm going to undo the bolt here at the end, and then I'll take my clamp, and I'll just re-thread my bolt just a few threads so it stays in place. I can take my rubber pad for my foot pack, and just fit that onto the bottom, and make sure that all the seams are closed there. We're then going to line it up onto our bracket that I've already installed. We're going to line up this piece here with this hole, and the smaller piece with the smaller hole. Once those are lined up, we'll extend that out, and then we'll take our longer Allen key and we'll just tighten down the bolts in the center here. What that's going to do is prevent that foot pack from moving up and down the length of the crossbar and just keep it secure in the spot that we need it.
We can now open our car doors and load up our crossbar. We're going to make sure when we load up our crossbar that the thicker end of the crossbar is facing forwards this side a bit, a bit bigger than the other side, we're just going to have that face the correct way. We're going to loosely install these, and readjust the other side. Perfect. With those in place we can take our tape measure, or flat tape at this time, and we're going to measure from the center of the foot pack to the center of the door jam here. All the measurements are in your instructions, but for now, we're going to use forty centimeters as our mark.
With this measurement, you're going to be able to put any kind of roof mounted accessories on your vehicle. You can do roof mounted bike racks, or cargo boxes, or even ski and snowboard carriers, which are all available on our website. We just have to double check that this side is even as well. A good thing to remember is that whatever we do to one side, we want to do to the other, just so our crossbar sits evenly and is secure. With those in the right spot we can now start to tighten down our foot packs. To do so, I'm going to take my tool and start by tightening the clamps so it sits just up against the door frame there.
We'll do the same to the other side. These bars are great, they're a sleek, aerodynamic design, they're going to be pretty light weight on your vehicle, and another great feature about it is that it does have a T-Track area to load up any of your T-Channel mounted accessories. One plus about that is that you don't have to take out this weather stripping here, you can actually leave that in and just push it down to load up those accessories. That's going to keep the aerodynamics of the crossbar and still prevent wind noise while you still have something on your crossbars. With those two up against the door jam, I'm going to start tightening them down. I do about five to ten turns on each side. If you heard that pop, that's going to be like a gas cap noise that you'll hear, that's when you know that your foot pack is completely secure and tightened down enough onto your vehicle, so now we'll just do the same thing to this side, make sure it is secure as well. We can close up our doors here and we'll grab our locking end caps. With those T-Track mounted accessories, as I mentioned before you can keep that weather stripping in, but these covers are also going to protect any kind of bike rack or anything that you have on there. Since they are locking you aren't going to be able to take your bike rack off without having that key and removing that end cap. It's just an added safety feature if you maybe don't have a locking mechanism on your bike rack. With those in place, that's going to complete our look at the Inno Aeroblade Roof Crossbars on our 2013 Volkswagen Jetta.
Average Customer Rating: 4.8 out of 5 stars (126 Customer Reviews)
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming.Waste of money. Most annoying couple hours spent in a long time. Extremely disappointed. Does not fit well. Not exactly a cheap option, but a cheap option in terms of fit and engineering. The instructions online and in the kits do not agree. But there is no helping the design. Plus there are no universal set of instructions--they are all individual items for the fit kit, the bars, etc. But a reasonably inclined person can figure it out so no big deal, but the engineering design is garbage--requires precise measurement yet the design is such that exact measurement is impossible due to the design.
Additionally, the parts are low quality Either low density plastic or easily stripped bolts. Even when as precise as possible, I wouldn't trust it with my kayak. What a mistake. Do yourself a favor and get a Yakima trailer or similar. It isn't that much more money in the scheme of things and then it isn't tied to your car. Can add a hitch to most vehicles anyway.
great bars, they have a slight curve to them so they look more natural, like they were made with the car, i went with 2 of the same size on my kicks, even though it was suggested to have one shorter, i think it looked much better in the long run.
These racks stay glued to your roof! Wouldn’t use any other system with older naked roofs
Quality looking. Very strong.
Racks were perfect for my Acura MDX. They fit like a glove and I have used them several times.
Has worked great for transporting my fishing Kayak as well as small loads of lumber. It has worked fine for about a dozen and a half boards at a time or a couple of sheets of plywood. Just make sure that you have a good way to strap them down as well as maybe a rubber mat to help hold everything in place. The noise from it on the high way can be a lot but certainly not as bad as some that I have heard. I figure that anything on the outside of a vehicle like that will produce some noise.
worked as expected, I used them to carry my hobie outback kayak (about 100lbs) on my Honda Civic 2016 Coupe (2 doors). They worked with no problem so far (1 year) even under high speed like 70mph.
We recently purchased 2 kayaks & Thule roof racks from our local outdoor store.
After waiting 2 weeks for our roof racks and J bars to come in we found that the Thule racks did not fit our 2017 Lincoln MKX and they didn't make any racks that would. The vehicle does not have roof racks and has a moon roof.
After a couple of days searching the internet we discovered etrailer.com. We found the Inno roof racks, but still was not sure they would work. We spoke to a repesenative and he assured us that the racks we chose would fit and the Thule J bars we did return would also work. As you can see by the photos 2 days later we were happy Kayakers.
This kit does not fit well. All measurements have been double and triple checked down to the millimeter. The lock on the covers interfere with the hooks. You have to apply so much pressure to get it to close that it makes the rack come loose. Not very satisfied
I bought these as part of a kit with 60" Aero bars and the appropriate kit for my 14 Flex. I spent probably an hour and a half double checking my measurements and getting them torqued down properly. I spaced the bars on top of the car just a little wider than proscribed because I was planning on carrying 4x8 plywood, and it looked better to my eye. One thing to watch for: The instructions for the car-specific kit (in my case INK263) show the foot spacing measurements for a square bar, and the measuring point for these feet and Aero bars is different. That measurement point is indicated in the instructions for the feet, not the kit. Same numbers, just different reference point. Otherwise, they look good and are rock solid.
Installation was a little tricky but once the "feet" were attached to the roof and the bars properly spaced, everything wrapped up very well.
There is no noticeable wind noise with these installed.
I did a lot of searching before selecting this rack for my Durango RT (no factory roof rails). It is easy to reinstall once the initial process is followed, I marked my doorjambs with a sharpie and it is easy to set up. Great product!
These are made perfectly for your vehicle. They are very secure when combined with the other Inno products. No worries of the rack system coming off. Using them to transport kayaks using kayak holders.
Packaging and shipping great....arrived a day earlier. Instructions were just ok. Had to figure out a few unclear steps. Front fit was perfect....the rear would not snug up and i went 1/4” measurements either way to eliminate any possibilities. Had to add about a 1/4” thickness to the rubber stay base in order for it to stay tight
These feet are easy to use and go well wit the Inno system. I was worried since my car did not come with any roof racks, but this is the solution to haul things on my roof. They work well and are very secure.
One was extremely hard to get on compared to the others (not sure if it had some rough machining or something), but once all we’re on, all was good
etrailer was the only vendor who had the custom fit roof rack feet I needed for my vehicle. I was trying to put a roof rack onto a Dodge Durango SRT...not a typical vehicle for this accessory! I looked everywhere for a suitable roof rack and thought I was settling by ordering the Inno kit from etrailer. I could not have been more wrong! I am so happy with the purchase!
I have had countless bike racks over the years and this is by far the best system I have ever had. Fits like a glove on my F150. Easy to install, looks great and the bikes do not move when on the roof.
Tule and Yakima did not have a rack for my Nissan murano. So it was a blessing to find the immo rack. It seems like it can fit any car model. It's strong and secure. I feel my equipment will be safe with this rack.
Started assembly last summer and finally completed installation this spring. Directions took a lot of attention to detail but were adequate. Rack went on car securely and looks great. Have attached kayak rack and a roof pod and both worked flawlessly. Would definitely recommend.
I’ve had the system in place for over a year now and haul dual kayaks often! I love it! The only thing I wish I could change is the wind noise that’s comes with it. But I’m sure with any rook rack system you get that.
Good product. Fairly easy to install for a DIYer. I've pushed them to their weight limits and passed with flying colors.
Once I realized which bar was the front one and which was the back it was a fairly easy install. Since the measurements for the foot placement were wrong in the instructions I would suggest not tightening the feet all the way to the bars until you put it on the car. It would have been nice if both sets of rubber pads were the same, with the tunnel hook, and if they had adhesive backing to avoid losing them. I added 2 sided tape.
Installation went pretty smoothly. The trick is to fully understand each step before moving to the next. There are a lot of small parts which at first was a little intimidating, but soon I was able to "get with it". I love the finished product and think you helped me get a good deal. Thank you for that
Product is great. Fits perfectly with some minor measurement adjustments. Can be assembled by one person, but helps to have two. Bought the complete roof kit and well as the Inno 80 basket for a Mazda CX3, took about two hours to assemble everything.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.