Customers compare V3092-603-00 to these similar products
Products Featured in this Video
Hi, John with etrailer. Today we're taking a look at Ventline's Ventadome manual roof vent that we installed on a utility trailer. So let's take a closer look at the roof vent. Now keep in mind what you're seeing right here. There is no lower trim panel on this one. This is just the vent by itself.… see more >
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Hi Christopher, There unfortunately isn't a guide to tell us the exact part numbers for the vents, skylights, etc. on your Passport. We offer a variety of plumbing vents and 12v fan vents but we unfortunately do not offer skylights. If you…
view full answer...If the roof on your enclosed cargo trailer isn't rounded too much then you actually don't need a pre-arched roof vent as you can see in the attached picture of the Ventadome #V2092SP-28 installed on an enclosed trailer. If your trailer is has…
view full answer...Since we aren't going to have any replacement covers or vents for a 13 inch by 13 inch roof vent hole the best option we can provide would be to open up the hole to 14-1/4 by 14-1/4 inch and install the #V2092SP-29 in it's place.
view full answer...Fasteners are not included with the Triple LED Trailer Tail Light #CE44VR. This is due to the different mounting surfaces that the lights can be mounted to. Depending on the surface that the lights will be mounted to will require different hardware…
view full answer...2-1/2 inch hitch opening are used on hitches that are Class V, and are designed to haul large heavy trailers. In order to reduce your hitch down to a 2 inch diameter opening on your new Ford F-350 Super Duty you would need to purchase a Curt Reducer…
view full answer...Yes, I contacted Fan-Tastic Vent and the replacement lift arm part #FVK8011-05 fits vents with domed lids. If your vent has a flat lid then you need the lift arm for flat lids part #FVK8014-05. I have attached two photos that show the difference.
view full answer...In order to connect the Wall Control Panel #MA59FR to your MaxxFan Deluxe Roof Vent #MA00-07000K, you need the MaxxAir RV Wall Control Communication Cable #MA69FR. This part is not included with the roof vent or the wall control panel, so you will…
view full answer...Yes, the replacement drop leg is part #BD500190, and is what you need for your Bulldog powered jack #BD500187. I called our representative a Bulldog to confirm as well. It will include the drop leg and pin. It's always a good idea to double-check…
view full answer...I checked with Bulldog and for the Bulldog trailer jack part #BD500199 that you referenced the correct replacement drop leg is the part #BD500190.
view full answer...The MaxxAir MaxxFan "Mini" Roof Vent w/ 12V Fan, #MA00-04401M and the MaxxFan Roof Vent w/ 12V Fan, #MA00A04401K are very similar but there is a difference in the profile. The MaxxAir Mini, #MA00-04401M will set at 2-7/8" above the…
view full answer...The first thing you will need is a battery and a battery box. The wiring for the light will need to be connected directly to this battery via a switch that you can get at a hardware store if the light does not already have a switch. Or you can…
view full answer...I went out and measured the outside to outside points on the flange for the MaxxAir MaxxFan, part #MA00-04401M, and it's 16-1/4 square. It does fit the standard 14 x 14 vent opening which is what you'll find on most trailers and it's for…
view full answer...