Customers compare F72FV to these similar products
Products Featured in this Video
Hi, everyone. Aiden, here, with etrailer. Today, we're gonna be taking a look at and showing you how to install these Fulton F2 Ratcheting, Retractable Tie-Down Straps for your boat. These are gonna be designed to be used as transom straps. They're two inches wide and up to 43 inches long. And the obvious benefit, here, is the fact that they are retractable.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
As far as the tire size discrepancy goes, I believe you have 12 inch diameter wheels, if you indeed have 4.80-12 tires. You can't fit a 12 inch tire on a 13 inch wheel, but if you measured the wheel from the wrong spot, you can easily come…
view full answer...Yes, replacement breakaway kit battery #HM20008 is the correct replacement for the Hopkins Engager system #20099. Its also the only replacement battery Hopkins offers.
view full answer...The overall measurement from the top of the roller to the bottom of the U channel is 2-1/2 inches. I have provided a photo for you that shows the dimension you inquired about. I have linked you to a parts review video for the Roller Bunk #DL21741…
view full answer...The Dutton-Lainson Roller Bunk #DL21741 that you referenced can be installed directly on top of your existing wooden bunks. According to the installation instructions when mounting over wooden bunks a 3/8 inch diameter lag screw is required. The…
view full answer...The inner diameter of bearing #L44649 is 1.063 inches. The inner diameter of bearing #L68149 is 1.378 inches. Both fit on a #84 spindle. The matching race for bearing L44649 is #L44610. And the matching race for bearing L68149 is #L68111. These…
view full answer...The Atwood Hydraulic Braking Assemblies 84210 are no longer made so replacement parts for them are not easily found. If you wanted, you could scour the internet and you might have luck finding someone with replacement parts for these in stock. That…
view full answer...Yes, the #AM25DR that you referenced would fit as a replacement rim for your trailer. It is 1/2 an inch narrower than what you currently have at 14 by 5-1/2 inches, but other than that it is the same dimensionally. Since these rims have a zero offset…
view full answer...We have a video review of the CargoBuckle G3 Retractable, Ratcheting Tie-Down Straps, #IMF18800, and I have linked it for you. Installation is straight forward. The straps have a mounting hole on the base and include nuts, bolts, and washers. All you…
view full answer...The Peterson Round Trailer Tail Light, part #431800, is a three function light and has two wires coming out of the back of the assembly. The brown wire is for running lights and the red wire is for turn signal and brake lights. The light grounds to…
view full answer...Yes, you can use a 25 Ft 4-Way Trailer Wiring Harness #A25W2GWB with a full length ground wire to ground your Tail Lights. You will not have to ground either the harness or the lights to the frame on your aluminum trailer. I recommend using Heat…
view full answer...The Optronics 25 foot 4 Way Wire Harness #A25W2GWB will be a good option. This will generally have enough length to cover most trailers. I will also recommend adding in a few of the Spectro Self-Stripping Connector with Waterproof Sealant…
view full answer...The Hopkins Endurance 4-way Flat Trailer End Connector, #HM48110, that you referenced is the harness that goes on a trailer, not a vehicle. The 4-way connector for your vehicle is the Hopkins Endurance 4-Way Flat Vehicle End Connector, #HM48030. You…
view full answer...