Customers compare E4139 to these similar products
Products Featured in this Video
Today, we're going to be taking a look at the front, center, or rear hanger, for double-eye springs. This hanger can be used as a front hanger on single axle applications, and it can be used as a front, center, or rear hanger, on tandem or triple axle applications. It's going to fit 1 3/4" wide double-eye springs with 9/16" diameter eyes. It does work with a 9/16" diameter bolt, hardware sold… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The standard diameter for trailer leaf spring bolts is 9/16 inch which is why the part #E4139 and all similar options have this hole size. We don't have anything with a smaller diameter but my guess is what you have is actually 9/16 inch.
view full answer...I reached out to our contact at Redline and he informed me that the Front/Center/Rear Hanger #E4139 is rated for axles ratings up to 7,000lbs. So you will be able to use these on your 2019 Grand Design Reflection 5th wheel.
view full answer...The only difference between a 4 leaf spring and a 5 leaf spring like the #e34SR is that the 4 leaf spring will use slightly thicker leaves and is 1/8 of an inch shorter. To get the best measurement of your existing springs, measure the center eye to…
view full answer...Both the MORryde Rubber Equalizers #MR87ZR and Dexter E-Z Flex Suspension Kit #K71-652-00 are achieving the same result. They are doing so with slightly different designs but end up with the same result. I recommend using the Dexter E-Z Flex…
view full answer...I measured the thickness of center hanger #115919 using digital calipers. The steel used to make it is 0.36 inches thick. I have linked a video review of this hanger for you.
view full answer...I went out into our warehouse and pulled a Front/Center/Rear Hanger for Double-Eye Springs, part #E4139, and measured the outside width of it. It measures 2-5/16 inches from the outside of one side of the #E4139 to the other side. Check out the…
view full answer...I spoke to my contact at Dexter Axle and they informed me that you may have the incorrect kit. There are currently two different E-Z Flex Triple Axle Suspension Kits for triple axle trailers which will depend on axle spacing. For example, if your…
view full answer...With 8 inches center to center hole that's a good start as these will flex between 7-1/4 to 8-1/4 measurements however you also may make sure you have the 35" center axle to center axle spacing and have 9/16" bolt holes. The #K71-657-00…
view full answer...The trailer leaf springs we carry are rated by the axle when used in pairs and not individually. Since you have 4,400 lb axles the 4,500 lb axle springs we carry part #e27SR would be the correct rating. Each individual spring is rated for 2,250 lbs.
view full answer...Thank you for the images. The MORryde Rubber Equalizers #MR87ZR are the correct set for your 2020 Keystone Outback Ultra-Lite 291UBH. You will pair this with the MORryde Suspension Upgrade Kit #MR46ZR. Instead of using the wet bolts included with the…
view full answer...Start off by placing your axle about 2/3rds of the way behind your trailer coupler. From there you'll need to fine-tune your axle placement until your trailer tongue weight is 10 - 15% the overall weight of your trailer. There isn't a set…
view full answer...The leaf spring hanger positions are largely dependent on which equalizers and leaf springs you will be using. For example, if you were to use the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs part #APT3 with the 5-Leaf Double-Eye Spring for…
view full answer...