Customers compare MCL13A2B to these similar products
Products Featured in this Video
Today we're reviewing part number MCL13A2B, from Optronics. This is a sealed mini LED light. It serves as a side marker, clearance, or identification light. It has two amber LED lights. And as you know, LEDs will last for thousands and thousands of hours, as opposed to a few hundred hours for incandescent bulbs. So if you're looking to upgrade your marker lights on your trailer, this would be a… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Thanks for the pictures of your lights! Based on that you'd want the part #328-003-19R for red lights that match what you have and #328-003-19A for amber. These ground through a white wire but you can run that white wire's ring terminal to…
view full answer...Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…
view full answer...When using an idler hub or a hub and drum with brakes on the Timbren Axle-Less Trailer Suspension System, part #ASR2000S02, the difference in the distance from the bracket to the front face of the hub as shown in the attached drawing would be the…
view full answer...The lights will need to be replaced, we have some great options for this. The Optronics LED Combination Trailer Tail Lights part #TLL160RK looks to be a great match for your existing taillights and the Custer Trailer LED Clearance Identification…
view full answer...What you can do is get some foam from a craft store and make a gasket for each of the lights #MCL31AB and #MCL31RB. Or you can use silicon sealant such as #0160297 or gasket maker such as #LT37464.
view full answer...When it comes to choosing a winch for a boat trailer, there are a few general rules we can use. The boat-size-to-winch capacity is generally 2 to 1. With good rollers and short winching distances, the ratio can increase to 3 to 1 and with wooden…
view full answer...The polished chrome ring, #A13C2B, is not required for mounting the sealed mini side marker lights, #MCL13A2B and #MCL13R2B. This is decorative trim ring only. The foam gasket, #A13G2B, would be used if these lights are mounted on the outside of an…
view full answer...The Optronics LED Clearance or Side Marker Light w/ Reflex Reflector part #MCL31AB mounts by running two screws like part #1131832 though the base. In order to access these screw holes you will need to remove the lens. I have attached a photo that…
view full answer...The light itself, #MCL13CA2B, is sealed so no worries of moisture getting into it. For the holes in the trailer to mount the light you could go with a silicone sealant such as #LT37467 which would be better than the foam gasket, #A13G2B. A…
view full answer...The Foam Gasket #A32GB is for your LED Clearance or Side Marker Trailer Light in Amber #MCL0032ABB or Red #MCL0032RBB.
view full answer...Yes, the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-655-35-EZ-K is what you need to upgrade to a 6-bolt pattern on your 2022 Forest River R-Pod 153 travel trailer. If you don't already have wheels with the 6 on 5-1/2"…
view full answer...I looked up your EZ Loader part number and it appears to be the same design as the part #AL91AB which for the matching grommet you'd then need the part #A91GB. You'll also need the wiring harness #A46PB.
view full answer...