Waterproofing Electrical Connections on Optronics Boat Trailer Tail Lights
Question:
I am replacing my broken Optronics taillights with the same incondensant lights. When making the wiring coonnections, is it ok just to use the wire nuts provided? Does the connection have to be waterproofed someway? If so, how can that be done?
asked by: Bryan K
Expert Reply:
The Waterproof, Over 80 inch Aero Pro Trailer Light Kit, # TL16RK, does contain the hardware needed for installation, but the lights and housing themselves are what is considered waterproof; they are sealed lights. The electrical connections for the wires are not waterproof.
What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection.
Another option is to use heat shrink tubing which is usually available just about anywhere tools and/or automotive parts are sold. With this you would first place the tubing around one of the wires before making the connection. Then use a butt connector to connect the wires. Slide the heat shrink tube over the connection and apply heat as per the directions. This will create a water tight seal as well. And I would still wrap that in electrical tape, too.
Products Referenced in This Question
Product Page this Question was Asked From
Optronics Trailer Light Kit for Trailers over 80" Wide - Submersible - 25' Wiring Harness
- Trailer Lights
- Tail Lights
- License Plate
- Rear Clearance
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Rectangle
- Kit
- Surface Mount
- Submersible Lights
- Incandescent Light
- 8L x 3W Inch
- Red and Amber
- Optronics
more information >
Continue Researching
- Shop: Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2 - LR D
- Article: Trailer Maintenance Schedule
- Shop: Andersen Trailer Hitch Lock and Adjustment Pin Lock Set - EZ Hitch and EZ HD Ball Mounts - Stainless
- Shop: CE Smith Offset Spare Tire Mount - Galvanized Steel - 4- and 5-Lug Wheels
- Shop: Go Power Portable Power Bank with Solar Panels
- Shop: Curt Tri-Ball Trailer Coupler Lock and Hitch Pin Lock
- Shop: Malone Foam Kayak Block for Truck Racks - 14" Long
- Shop: CE Smith Spare Tire Mount - Lockable - Steel - 4-Lug and 5-Lug Wheels - 8-3/4" Long
- Q&A: Solution for Securing Jack Handle from Dragging On Ground In Trails
- Video: Deka Primary Wire Heat Shrinkable Tubing Review
- Q&A: Trailer Light Kit Recommendation for Ranger Boat Trailer
- Search Results: heat shrink butt connector
- Search Results: heat shrink connector
- Search Results: heat shrink
- Q&A: Product to Hold Kayak Paddles on a Trailer While Traveling
- Q&A: How to Waterproof Trailer Light Connectors on a Nitro Boat Trailer
- Q&A: Does the Trailer Wiring Need to be Waterproof on a Boat Trailer to Avoid a Short or Damage
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Search Results: 25580
- Video: Kenda Tires and Wheels - Tire with Wheel - AM32424 Review
- Shop: Trailer Hitch
- Article: Trailer Tire Sizing
- Shop: Trailer Wiring
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Trailer Wiring
- Search Results: 44649
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: dust cap