How to Waterproof Trailer Light Connectors on a Nitro Boat Trailer
Question:
Bought a replacement light from you. It is for a nitro boat trailer, I pulled the light off and it has a black triangular 3 wire connector on the light and on trailer wire. Is there special connector to keep water proof?
asked by: Tim D
Expert Reply:
What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection.
Another option is to use heat shrink tubing which is usually available just about anywhere tools and/or automotive parts are sold. With this you would first place the tubing around one of the wires before making the connection. Then use a butt connector to connect the wires. Slide the heat shrink tube over the connection and apply heat as per the directions. This will create a water tight seal as well. And I would still wrap that in electrical tape, too.
I still would recommend you disconnect your trailer connector prior to backing the trailer into water.
Products Referenced in This Question
Product Page this Question was Asked From
LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 23 Diodes - Driver Side
- Trailer Lights
- Tail Lights
- License Plate
- Rear Clearance
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 8L x 3W Inch
- Red
- Optronics
more information >
Continue Researching
- Shop: Trailer Wiring Junction Box - 7 Color Coded Terminals - ABS
- Shop: Trailer Wiring
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Q&A: Replacement Grease Seals for Dexter Part # 010-036-00 on a 7,000lb Trailer Axle
- Q&A: Should The Breakaway Switch Be Wired Through a Circuit Breaker On Travel Trailer Battery?
- Article: Trailer Wiring Diagrams
- Shop: Grease Seals 10-36 (pair)
- Search Results: break away switch
- Search Results: break away switch
- Q&A: What is the Difference Between Self-Adjust and Nev-R-Adjust
- Q&A: Comparing the eTrailer and Dexter Electric Trailer Brake Kits
- Shop: Replacement Breakaway Switch for Bright Way Trailer Breakaway Kits
- Shop: Replacement Switch for Curt Soft Trac I and II Trailer Breakaway Kits
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7K
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K
- Q&A: What Size Thread/Nut Does Buyers Products Junction Box # 3375601101
- Video: Buyers Products 7 Color Coded Terminal Trailer Wiring Junction Box Review
- Video: Buyers Products Wiring 3375601101 Review
- Q&A: How to Test the Hopkins Engager Trailer BreakAway Kit
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer brake wiring kit
- Q&A: Troubleshooting Weak Trailer Brakes When 2023 Ram 3500 Brake Controller is at Full Power
- Video: Review of Dexter Axle Trailer Axle Parts - Wiring Grommet - 046-124-00
- Search Results: trailer frame wire clips
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Video: Peterson Piranha LED Trailer Light Review
- Video: Review of Peterson Trailer Lights - Clearance Lights - M170A
- Search Results: submersible led trailer lights
- Search Results: plugs
- Video: Optronics Square LED Trailer Clearance Light Installation