Trailer Wiring Harness for 2004 Mitsubishi Endeavor
Question:
Im thinking about getting T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - Mitsubishi Endeavor, 2004 My Endeavor does not have the trailer package. I was reading on other sites that their cable would not work because I did not have the correct wire harness on my vehicle. Can I just plug your harness into my existing connectors? Thanks
asked by: Dan
Expert Reply:
The connector on the Curt # C56039 T-Connector would indeed plug into the trailer connector plug located in the cargo area, under the carpet next to the driver's side wheel well as shown in the photo. Just to be sure, I contacted our representative at Curt, who assured me that the # C56039 trailer wiring harness is compatible with all models of the 2004 Mitsubishi Endeavor.
If you don't yet have a hitch, I'd recommend the Curt Class III # 13569. This hitch has a bolt-on installation and will provide you with a 2" hitch receiver, which is the most common size used for hitch mounted accessories.
If you don't already have a ball mount and trailer ball, you can use the # D-4 ball mount, Hitch Pin and Clip, # PC3, and # 63845 for a 2 inch ball or # 19260 for a 1-7/8 inch ball.
![Mike L](https://images.etrailer.com/static/images/catg/people/166_tn.jpg)
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)