Looking for LED Version of # AL91RB Mini Rectangular Clearance/Side Marker Lamp

Question

Question:

Do you have the exact same light in an LED version?

asked by: Rich C

0

Expert Reply:

You bet we do! For the LED version, you'll need part # AL91RB. The lamp can be grommet mounted using # A91GB or surface mounted using a self grounding base like # A91BB for black/ # A91CB for chrome or a standard base like part # A91BOB for black/ # A91OB for chrome.

If you use a self grounding base, use the single wire pigtail, part # A91LW or for the standard base, use the two wire pigtail, part # A49PB.

expert reply by: Mike L

0

Answer 1

Yes, the Peterson LED Identification Light Bar #M191-3RL that you referenced would work great on your 2005 Nitro boat trailer as this is submersible and universal enough that it can easily be made to fit a boat trailer like yours.

view full answer...

Answer 2

For the clearance light part #AL91RB we have the grommet part #A91GB which is basically a hard rubber.

view full answer...

Answer 3

For the clearance light #AL91RB and the matching amber light you would install the lights in the appropriate bases like #A91BB and then use 2-wire pigtail #A46PB, plug it into the backs of the lights and attach the wires to the existing trailer…

view full answer...

Answer 4

According to my Optronics representative, the #AL91RB marker/clearance light you mentioned is a direct replacement for the Truck-Lite 15 series. The Signal Stat 1500 is how Truck-Lite refers to the same lamp in its LED version. A mounting bezel is…

view full answer...

Answer 5

The Optronics Sealed Micro-Flex LED Trailer Side Marker #MCL50RB referenced in your question does have polarity, but the PL-10 Plug #A46PB that you also have is designed so that it can only be plugged in one way. This is essentially how you will know…

view full answer...

Answer 6

The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this you'd need the part #A46PB and then for a grmmet part…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Looking for LED Version of # AL91RB Mini Rectangular Clearance/Side Marker Lamp

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching