Can the Thule Snug Tite Lock be Used While Driving with Bike Rack Installed

Question

Question:

HelloI just installed the Snug Tite lock and wonder if its made to drive with while installed or do I have to install the regular hitch bolt when driving?

asked by: Paul M

1

Helpful Expert Reply:

You can leaving the Thule Snug Tite lock # THSTL2 on while driving. It is basically the same thing as the regular hitch bolt. The only difference being the end of the pin which is notched to accept the lock. So yes, you can absolutely drive with it in place.

expert reply by: Michael H

1

Answer 1

The Threaded Anti-Rattle Hitch Pin Lock for etrailer Cargo Carriers #e99047 uses an M16 bolt while the Thule bike racks fit with an M12 bolt so they unfortunately aren't compatible. This just means that you need to use the Thule Snug Tite…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 5

To keep your back end from squatting, I recommend the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension item #CSS-1094R. These insert into your rear springs and keep your suspension from being pushed down by the weight of your…

view full answer...

Answer 6

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 7

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Answer 8

Yes, there is! It is the Draw-Tite item #76271. This hitch is custom fit for the 2024 Subaru WRX and bolts to it with included hardware. It is a class III hitch with a 2" receiver that has a 3,500 lbs towing capacity and a 525 lbs maximum tongue…

view full answer...

Answer 9

Thanks so much for the photos, they were very helpful, and based on that and the fact you mentioned it was from 2009, I am almost certain that what you have there is the Thule Roadway 914 bike rack. We do in fact have the correct 1-1/4" to…

view full answer...

Answer 10

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 11

There's not much of a difference in the 2" hitches available for the 2023 Toyota RAV4. The Draw-Tite item #DT82QR, Curt item #C13416, and etrailer item #e23ZR all look identical when installed. With this in mind, I recommend going with the…

view full answer...

Answer 12

The Thule Apex Swing XT #TH9027XT is a great option for a 2-inch hitch receiver. The nice thing about having the Apex's swing-away feature is that it lets you access your rear cargo area on your 2018 Subaru Outback Wagon without removing bikes…

view full answer...