Location of Under-Dash Brake Controller Connector on 2014 Ford Explorer

Question

Question:

Can you tell me for sure where the connector is on a 2014 explorer I cannot find it Ford says left kick panel but it is not there one forum I read behind glove box and one near steering column/brake release

asked by: Gregg

0

Expert Reply:

The brake controller connector is located directly behind the hood release handle on your 2014 Explorer. Ford typically uses a gray plug, but it might also be a light brown in color.

I have confirmed this for certain w/ my Tekonsha representative.

If the plug is present, you'd use the # 3035-P wiring adapter to connect your Tekonsha brake controller to the connector under the dash. If your Explorer doesn't have the factory 7-way trailer connector, the plug might not be present. If this is the case, the brake controller would need to be hardwired using our brake controller installation kit, part # ETBC7. The kit contains everything needed to install a brake controller, including a 4-poke to 7-way adapter, hardware, wire and circuit breakers, but if your Explorer doesn't have the 4-pole, you'd need to install one using # C59236.

I'll link you to the installation instructions for the ETBC7 kit.

expert reply by: Mike L

0

Answer 1

On a 2014 Ford Explorer, the brake controller port is located by the steering column. The brake controller adapter you would need to use a Tekonsha brake controller like our best selling P2 part #90885 is the part #3035-P. For a brake controller I…

view full answer...

Answer 2

The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part #APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that…

view full answer...

Answer 3

According to the owner's manual, when activated by pressing the button, the Tow/Haul feature improves transmission operation by changing the shift points so that upshifts are delayed to keep the engine operating higher in its power band when…

view full answer...

Answer 4

With just the one connector you referenced, the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector #C56278 or the #C56306 will work well. I've attached a video that shows this installation with just the single connector to…

view full answer...

Answer 5

When installing the Curt T-Connector Vehicle Wiring Harness #C56306 (which is custom fit for your Explorer), you will want to follow the written instructions that came with the harness and ignore the connector. The connector is not necessarily a…

view full answer...

Answer 6

It sounds like you're having an issue with the installation of the 7 way connector that came with the Curt #C56306, and we can absolutely help you get this resolved. I'll start off by saying that the wiring colors are going to be a general…

view full answer...

Answer 7

The Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector #C56306 you asked from is a fit for the 2011 - 2019 Ford Explorer without factory Tow Package. Based on what you mentioned it sounds like the trailer wiring isn't working…

view full answer...

Answer 8

If your 2013 Ford Explorer has the trailer wiring (it should) it would be located under the passenger side rear fender. If you check out the install video I attached you can see our installer point it out at the 16 second mark. To install a 7-way you…

view full answer...

Answer 9

I have a super easy brake controller solution for your 2017 Ford Explorer with the Curt Echo brake controller part #C51180 which plugs into an active 7-way and once synced to a smartphone is ready to tow. For an easy to install 7-way kit all you need…

view full answer...

Answer 10

The Draw-Tite Mounting Bracket #18138 referenced in your question is designed to mount most standard 7-Way connectors. To ensure this will work with your existing 7-Way, I recommend taking a couple measurements on the connector. This mounting bracket…

view full answer...

Answer 11

The best way to determine if your Explorer is equipped with the tow package is to check with your Ford dealer. They should be able to run the VIN and be able to tell you exactly how the vehicle was equipped. I'm assuming you're needing the…

view full answer...

Answer 12

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Location of Under-Dash Brake Controller Connector on 2014 Ford Explorer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching