Replacement Cover for Pace Edwards JackRabbit Tonneau for 2011 Ford F-250 Long Bed

Question

Question:

2011 F250 Pace Edwards Jack Rabbit direct replacement Tonneau cover only.

asked by: Dona

0

Expert Reply:

Hey Dona, for your 2011 Ford F-250 long bed that has a Pace Edwards JackRabbit tonneau cover the correct replacement cover/tarp would be the part # PE93QJ.

expert reply by: Jameson C

0

Dona

5/2/2024

Do you offer a video for installation of the cover only?

Reply

Jameson C.

5/3/2024

@Dona We haven't had a chance to shoot an install video yet for the replacement cover.

Reply

Answer 1

Hey Dona, for your 2011 Ford F-250 long bed that has a Pace Edwards JackRabbit tonneau cover the correct replacement cover/tarp would be the part #PE93QJ.

view full answer...

Answer 2

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 9

From the looks of the photo you sent it does not look like you have an OEM suspension system on your boat trailer. I recommend securing the suspension rail to the trailer frame in a more secure manner like drilling and using bolts so that it does not…

view full answer...

Answer 10

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 11

The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this you'd need the part #A46PB and then for a grmmet part…

view full answer...

Answer 12

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Replacement Cover for Pace Edwards JackRabbit Tonneau for 2011 Ford F-250 Long Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching