Parts Needed To Install 5 On 5-1/2" Bolt Pattern Hubs On a 1987 M105A2 Trailer
Question:
I have a 2008 jeep wrangler 2 door on 4 inch taraflex lift I just bought a 1987 m105a2 trailer I wont to bould a overland trailer that is level with my jeep running the same tires and rims I believe it 5 on 5.5 on the jeep I have a picture of the set up before I put the lift on the jeep
asked by: Kevin F
Expert Reply:
To be able to run the same 5 on 5-1/2" bolt pattern for your Jeep Wrangler on the M105A2 trailer you are going to have to cut off your current spindles to have 2 Spindles # TRU77FR installed. This is the common size spindle found on a 3,500lb axle which will then let you install 2 of the Hub/Drums # AKHD-555-35-EZ-K. With these you will want to install Electric Brakes # 23-468-469 since they are much better on an Overlanding trailer than surge type brakes. We do have a Junction Box # 3430001-JBK and Trailer Breakaway Kit # 3802346 to help with the electric conversion for the trailer.
Please let me know if you need any help finding the wiring parts for your Jeep if you do not already have a 7-way or controller.
Products Referenced in This Question
Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Junction Box and Installation Kit for Autowbrake Trailer-Mounted Electric Brake Controller
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- Junction Box
- etrailer
more information >
Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Side Load
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- 1 Amp Charger
- Battery Included
- 5 Ah
- Bright Way
more information >
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 5-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles
- Trailer Spindles
- EZ Lube Spindle
- Round
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Q&A: Trailer Grease Seal to Replace 127194TB
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Article: How to Charge a Dump Trailer Battery
- Q&A: Does Correct Track Trailer Alignment Kit # RR23QX Come with Enough Brackets for Tandem Trailer
- Q&A: How Does the Correct Track Trailer Alignment and Lift Kit Really Work
- Q&A: Will the Correct Track Trailer Alignment and Lift Kit Prevent Nose High Towing
- Q&A: Recommended Replacement For A WFCO WF-8750P Power Center
- Q&A: Replacing Parallex 7345 Converter to One that is Compatible with Lithium Batteries
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: Trailer Maintenance Schedule
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Trailer Hitch Receiver Sizes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Most Popular Wheel Bearings
Kevin
3/11/2024
I was wanting to go with axeless setup for independent suspension I just don't know now if I bought the right trailer do to weight I'm stripping the trailer down to frame and bed to reduce weight I'm just not sure if it will be enough